Question about 1995 Mazda MX-6

Open Question

WHERE IS THE CRANK SENSOR ON MAZDA MX6 1995 ?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to find out where the crankshaft sensor is located on Mazda Tribute 2002? Need to change it


2004 Mazda tribute 2.0l manual transmission cranks position sensor tip worn / rubbing. p0351, p0352, p0500, p0320 codes. I have a 2004 Mazda tribute with 2.0l 4 cylinder. 140,000 miles. First problem was it would not start but I could hear the fuel pump run and the engine cranked over. I checked for spark and all four plugs had no spark. p0351, p0352, p0500, and p0320 codes displayed.
I have 12 volts at coil. I decided to remove and inspect crank sensor on the transmission side of the engine ( on engine below thermostat housing bolted to engine block) once i removed it i noticed the tip of the sensor was broken, yes, broken. so I knew i found the problem.
I put a new crank sensor in and the car started but ran for 1 hour idling as if a cylinder was not firing. Then it would not start ever again. I removed my brand new replacement sensor to find the tip was rubbed off enough to see the inside metal. i think it could be a possible warped flywheel but I am having trouble finding diagrams of the excitation part of how the crank position sensor works.
I believe the flywheel has holes that excite the sensor. The tribute does move and clutch works for the hour I had it running, so the manual Trans does work as well as the clutch.
https://electronicshelponline.blogspot.com/

Jul 16, 2016 | 2002 Mazda Tribute

1 Answer

New Crank shaft pulley was installed, then Mazda Tribute 2.3lL won't start


check for damage /wire connections to the crank shaft position sensor near the harmonic balancer pulley. Check the air gap of the sensor

Apr 15, 2014 | Mazda Tribute Cars & Trucks

1 Answer

Mazda 323 ignition


run fault codes and look for cam/ crank position sensors faults. check that the cam shaft is turning ( broken timing belt/chain). Check that the immobiliser is operational.

Feb 14, 2014 | Mazda Cars & Trucks

1 Answer

Volvo 2005 EC210 BLC Engine Crank but no start .display shows code 140SID and 250 9


It can be faulty fuel pump or clogged fuel filter or its issue with starter or battery or may be problem with sensors.There are few possibilities that can cause these problem,there are few help links provided related to these issue. Click the link below and refer the troubleshooting procedure to solve the problem:-----
Engine cranks but will not start? http://technoanswers.blogspot.in/2012/02/engine-cranks-but-will-not-start.html
-------- Landcruiser prado won't start http://technoanswers.blogspot.com/2012/10/landcruiser-prado-wont-start.html ------- 2007 ford expedition engine cranks but wont start http://technoanswers.blogspot.com/2012/10/2007-ford-expedition-engine-cranks-but.html

--------
: Engine Cranking Fast but not Firing up? http://whatisbyme.blogspot.in/2012/05/1999-lexus-gs300-engine-cranking-fast.html

----------
1997 Oldsmobile Cutlass Ciera: The Engine cranks but not start? http://schematicsdiagram.blogspot.in/2012/04/1997-oldsmobile-cutlass-ciera-engine.html

-----
Mazda MPV cranks but will not start? http://technoanswers.blogspot.com/2012/01/mazda-mpv-cranks-but-will-not-start.html
-------- MAZDA MPV WILL CRANK BUT NOT TURN OVER TO START? http://technoanswers.blogspot.com/2012/01/mazda-mpv-will-crank-but-not-turn-over.html
--------- Vehicle Cranks Fast but Won't Start http://whoisbyme.blogspot.in/2012/07/vehicle-cranks-fast-but-wont-start.html

------
How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html

---------
These details will help,keep updated for more help.

Oct 16, 2012 | Cars & Trucks

1 Answer

HOW DO A CRANK SENSOR LOOK ON A MAZDA PROTEGE?


check this out on autozone.com web site at plus it depends on the liter of engine but you ca add your liter engine but here is one on there web site at : http://www.autozone.com/autozone/parts/1995-Mazda-Protege/Crankshaft-Position-Sensor/_/N-j1kmtZ8znbj?filterByKeyWord=crank+sensor&fromString=search

Jun 02, 2011 | 1995 Mazda Protege

1 Answer

Mazda mvp 03 spark plugs #5 and #6 are not firing. I pull the conector at idle and nothing. Ive cleaned and checked the injectors. New spark plugs. Ive checked fire, fuel and compression. All seems...


no the bad oxygen sensor never affects misfire it affects only the air/fuel mixture
those are causing misfire (a bad coil, ignition module, distributor pickup, crank sensor,).
and i doubt the
crank sensor cuz computer says sensor even if it said to be o2 but no its the crank one its ok if computer fault
i hope my answer was useful

May 30, 2011 | 2002 Mazda MPV

1 Answer

Looking for the location of crank shaft on 2000 mazda 626


i assume you mean crank shaft sensor ,if its not on the front puilley then look around the bell housing in the most extreme awkard in accessable position possible because you can bet that is where it is

Jun 14, 2010 | 2000 Mazda 626

1 Answer

1995 MAZDA Protege


When you replaced it with a used one , it was a gamble and one you lost ,time to buy a new one ENJOY

Nov 08, 2008 | 1995 Mazda Protege

Not finding what you are looking for?
1995 Mazda MX-6 Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...