Question about Cars & Trucks

1 Answer

Will the hazard lite switch being pulled oit effect the brake lites

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 44,109 Answers

Yes, it will.

Posted on Dec 09, 2016


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Which fuse controls brake lights? On a 2005 buick rendezvous 2wd

My info says hazard/flasher fuse in center console fuse box. You could also check proper colors at brake switch, the brake switch should be activated by brake pedal arm. Orange wire is hot all the time. White wire goes hot when brake switch is activated. Are the high-mount and lower brake lites both out?

Jan 29, 2016 | Buick Cars & Trucks

2 Answers

How to check brake light switch

You should have power into the switch on the lite green and red wire, then power out on the lite green wire.

Jun 25, 2013 | 2001 Ford F150 Styleside SuperCrew

1 Answer

95 mustange gt brake light dont work check #9 fuses change all bulbs replaced switch on brake pedal hazards lights works ,parking or running lights works,turning signal lights works,what other places i...

I assume the fuse has power if the hazards work.
The third brake light skips the turn signal switch, the regular brake light circuit goes thru the turn signal switch.
Do you have power going into the turn signal switch on the red lite green wire from the brake switch ?

Feb 17, 2013 | 1995 Ford Mustang

1 Answer

My tail lights, turn signals, hazards and third brake light works, but my brake lights do not.

Check your brake lite bulb socket alot of times even a newer car will go bad from heat ing every time bulb comes on,,also check for grd on that socket, also should check brake lite swich on brake peddle

Mar 11, 2011 | Ford F-250 Cars & Trucks

1 Answer

Stop lites out but stop lite in back window works. Blinkers and hazard work. The fuse box contents do not match the fuse box diagram. Only think I noticed is that the ABS light does not come on at all...

An easy way to test the switch is to jumper the wires together. If the brake lights come on you know the switch is bad. If not, then you have to look elsewhere in the system to solve the problem.

Nov 12, 2010 | 1995 Buick Regal

1 Answer

No brake lites, 1993 Jeep Wrangler 4-cyl tail lites work, turn signals work, and hazards work. Is it a bad brake switch?

yes, or the relay.

Please see my tip at . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Oct 10, 2010 | Jeep Wrangler Cars & Trucks

1 Answer

I need to replace the turnsignal switch, where is it located. I have no turn signals right or left. The park lites, hazard lites and brake lites work. The turn signal switch needs replacing, where is it...

the switch located inside the steering collum also as
I don't know what year your car is but if it is 1990 or
above it is air bag equiped this means the bag has to
be removed to pull the wheel,
If you have no experiance with air bags please consult somone who has it can be dangerous.
if you have any more ? gimme a buzz good luck

Jan 12, 2010 | Cadillac DeVille Cars & Trucks

1 Answer

Hi. 91 bronco no stoplites or hazards.powr out of fuse box no powr at sockets. tail lites wurk fine. i tried 2 run makshift grd but no lck.directnls r fin and hazards wurk in front, its like both rh and lh...

heck power on both sides of brake light switch with pedal depressed.if power on 1 side only replace brake light switch.if no power to brake light switch check turn signal switch.

Jan 02, 2010 | 1991 Ford Bronco

1 Answer

1982 chevy van no brake lights everything else works new brk lite switch dont no what to do now HELP

Check for power in and out of the switch with brake pedal depressed.If ok check to see if your hazard lights work you could have a faulty turn signal switch your brake lights feed through the T/S switch.Also make sure your bulbs are good.

Dec 23, 2009 | 1992 Chevrolet C/K 2500

1 Answer


The switch has a small plunger that has been pushed in too far. These are self adjusting units. You must pull out on the plunger with the brake pedal pressed, you will here it make noise as you pull out. This is normal then just release the brake and the pedal will set the length of the plunger for you. NOTE do not pull up on brake pedal, this will throw your adjustment off!

Aug 13, 2009 | Dodge Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14512 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides