Question about Cars & Trucks

Open Question

I need some help for my car i need to replace the thruttle position sensor, do i have to twist the spring

Posted by on

  • Brad Brown Dec 09, 2016

    Hi Michael Valenzuela, I want to help you with your question, but I need more information from you. Can you please add details in the comment box? Year make and model

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Throttle positing senser on a 99ranger I changed it now the idle is way to high


The positioning of the new TPS IS OFFSET....It is possible to install it wrong by accident..I have seen this happen before..The pressure from the sensor plastic actuator has been installed and slightly twisted against the throttle lever inside which causes throttle to raise slightly....Wear safety glasses and disconnect battery..Remove sensor slowly and carefully while removing and watch the throttle lever inside to see if it moves in any direction...Carefully install it again making sure it doesn't twist the throttle lever inside where sensor mounts...The lever on the sensor should stay in its position...Carefully install sensor making sure it doesn't twist...Connect wiring and battery and start for a safety check.....It is possible to have a wrong sensor or faulty new sensor...Double check that it is the correct sensor...

Mar 01, 2015 | Cars & Trucks

1 Answer

Audi a4 56plate . when putting the thruttle down the car shutters, hesitates


Try unplugging the Mass Airflow sensor and see if the car runs better, if it does replace the MAF sensor. It is located in the air intake hose to the engine.

Feb 16, 2012 | Audi A4 Cars & Trucks

1 Answer

Replace rear drum brake pads


for the best help in this you really need to invest $25 in a manual for the vehicle. Here are the basic steps:
-jack up & remove wheel
-slide off drum (emergency brake off)
-remove springs between shoes, parking brake cable, pin thru backing plate with spring and twist cap retainer holding shoes to backing plate, draw or take a picture of each side before you disassemble as they may not be the same exactly on both sides
-check drum thickness & condition (have turned by shop or replace as required)
-rotate adjusting stars in all the way so that new assembly is not spread too wide to fit back in drum
-clean all parts well and re-assemble, use brake cleaner spray only! lubricate friction points of backing plate with high temp lithium grease-very small dab only! (important to double-check all the spring positions and levers and mechanical pieces during re-assembly
-brakes will self adjust to correct position while in reverse and applying pedal you may hear them clicking

Sep 30, 2010 | 2000 Dodge Caravan

2 Answers

How to get coorect position for upper spring perch on 1994 diamante?


Hello,

Thanks for using FixYa.

There is no specific position for the spring perch. Just assemble it with the spring an shock absorber, put the screws back and you should be good to go.

HotRatchet

May 16, 2010 | 1994 Mitsubishi Diamante

1 Answer

How do i replace cam positioning sensor in 2003 4.7 dodge durago


Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.

Apr 07, 2010 | 2003 Dodge Durango

1 Answer

Hi have a ford focus 1.8 zetec 1999 trying to replace the speed sensor i have removed the retaing pin eventually however im having difficulty removing the sensor still its stuck tight are there anymore...


pulls out but are very tight try warming the area round sensor very carefully with a hot air gun then try and twist it i have had them where i have had to drill hole in sensor screw in slide hammer to remove

Feb 08, 2010 | 2000 Ford Focus

1 Answer

2005 sonata both front seat belts stuck in out position


retractr springs mighr be pucked or it could just be twisted you need to take off the pannel to find out

go to the auto recyclers if the springs are pooched
they are a lot cheeper than the dealer

Dec 31, 2009 | 2005 Hyundai Sonata

1 Answer

I need to replace the crank sensor on my 96 dodge with 5.9 cummins engine it i can not find it


The Camshaft Position Sensor (CMP) on the 5.9L diesel engine is located (1) below the fuel injection pump. It is bolted to the back of the timing gear housing (7).

1. Disconnect electrical connector at CMP sensor.
2. Remove sensor mounting bolt (6).
3. Carefully twist sensor from timing gear housing.
4. Check condition of sensor O-ring.

INSTALLATION

1. Clean out machined hole in back of timing gear housing (cover).
2. Apply a small amount of engine oil to sensor O-ring.
3. Install sensor into timing gear housing (cover) with a slight rocking action. Do not twist sensor into position as damage to O-ring may result. CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to back of timing gear housing (cover). If sensor is not flush, damage to sensor mounting tang may result.
4. Install mounting bolt and tighten. Refer to Torque Specifications.
5. Connect electrical connector to sensor.

Oct 17, 2009 | 1988 Dodge D-Series Pickups

1 Answer

Replacing bad camshaft position sensor


  1. Disconnect battery ground cable.
  2. Remove water pump pulley attaching bolts, then the serpentine belt and water pump pulley.
  3. Disconnect sensor wiring connector and remove sensor retaining bolt.
  4. Twist and pull sensor to remove.
Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring.

It is located under the water pump. Make sure when you remove the sensor that you rotate the crank shaft and look in the hole to make sure the pick up magnet is still in there. Sometimes they come loose and cause a no start or long crank. You will need to have the code cleared still.

May 06, 2009 | 1991 Pontiac Bonneville

1 Answer

04 Dodge SRT 4 crankshaft sensor


The Crankshaft Position Sensor is located directly next to the starter.
  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Aug 15, 2008 | 2004 Dodge SRT-4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...