Question about Cars & Trucks

2 Answers

What could be the problem if my turn signals stop working on my 2006 hyundai azera. i have low beam lights but want turn on bright

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

If your headlight on off switch is also your turn signal switch and high low switch then it is likely the switch.

Posted on Jan 31, 2017

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,335 Answers

Check your fuses first and then check your hazard flasher relay. As for your high/low beams, could be your head light switch itself.

Posted on Dec 09, 2016

  • 5 more comments 
  • derrick royster
    derrick royster Dec 09, 2016

    the signals work when i turned the flashers on. i checked the fuses and they are good. i also changed the combination light/windshield whipper switch. the signals still dosent work and my lights want change to high beam

  • derrick royster
    derrick royster Dec 09, 2016

    i also checked the fuses with a tester while in the fuse box and maybe half wouldn't make the tester light up but when i switch out fuses the tester would light up then. could it be the fuse box itself or the wire connection to the fuse box?

  •  SeabeeMechanic
    SeabeeMechanic Dec 09, 2016

    You said that your turn signals stop working, does this happen after you have them on for a few seconds ? If yes, then most likely if your flasher relay. Have you replaced this component ?

  • derrick royster
    derrick royster Dec 09, 2016

    no they just stop working completely along with the dimmer and i only have one speed on the windshield whipper control. lights,signal and dimmer on left control and whippers on right control but connected like bunny ears

  •  SeabeeMechanic
    SeabeeMechanic Dec 09, 2016

    Do you have the covers and steering wheel removed to access the harnesses that connect to the switches ? Might want to trace them all the way back to fuse panel and see if wiring is damaged.
    Have you checked the dimmer also ?

  • Casdie Jan 28, 2017

    Did you figure out what the problem was. I'm having the same issue

  •  SeabeeMechanic
    SeabeeMechanic Jan 31, 2017

    You might want to check your flasher relay to include power / ground and wiring.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the headlight relay of hyundai grace


If they don't come on, Look at the fuses. Pull them out and look. This takes care of corrosion problems. If you only have low or high beams. Replace the turn signal switch. The only light relay is the turn signal switch.

May 10, 2014 | 2006 Hyundai Sonata

1 Answer

Low beams wont turn on brights will


check that you have power from the light switch to the relays to trigger the relay to turn the lights on. IT may be a faulty light switch--- fuse --light module control unit.

Jan 28, 2014 | 2009 Saturn VUE

1 Answer

2006 Hyundai Tycson GL Headlight Problems


Could be a defective headlight relay, Located in the fuse block in engine compartment,

Nov 29, 2012 | Cars & Trucks

1 Answer

1998 Hyundai Accent L 1.5L SOHC 5speed......My Headlights low/high beam and heater dont work???


Get a schematic and trace out the power source to those devices not working.

Sep 07, 2017 | Hyundai Motor 1998 Accent

1 Answer

My light problem is i have low beam on right side no low on left side i turn highs on and right side goes out and high on left turns on then when back to lows beams and i pull turn signal to flash high...


If you have separate bulbs for the low and high beams(4 light system), if you pull the turn signal and hold it, all 4 lights will stay on until you release the turn signal. You need to replace the bright bulb on the right side and the low bulb on the left side. If your headlights only have one bulb on each side, then you will have to replace both of them to get everything to work.

Jan 04, 2011 | 2000 Ford Mustang

1 Answer

High beams shine too close to the vehicle. How do you only adjust high beams without disturbing low beam alignment


The alignment of the head lights aligns both at the same time since there is only one bulb. It sounds as if the bulbs may be the problem. The filament in the bulb may be starting to go bad, or if bulbs are new the filments are bad. If the low beams are also off check that bulbs are installed and seated properly. If they are they will need alignment. If alignment is needed go to a shop that has the tool ta align head lights, They don't just pull car up to a wall and guess that its right or close.

Oct 14, 2009 | 2006 Hyundai Azera

2 Answers

Low Beams suddenly stopped working


SURE!...Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it. OR --- Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Oct 02, 2009 | 2006 Hyundai Elantra

1 Answer

I need headlight adjustment specs for a 2006 Hyundai Azera.


that shadow cutoff is normal. It's to reduce glare for oncoming drivers

Apr 03, 2009 | 2006 Hyundai Azera

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...