Question about 2001 Ford Windstar

1 Answer

How do you rest a 2001 Ford Windstar after having wheel bearings installed.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 11,447 Answers

Reset what ? Replacing wheel bearings doesn't require restting anything ! What did you do ? is the question

Posted on Dec 09, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 Ford Windstar Speedometer stopped working after I installed Hub Bearings


The sensor is attached to the output shaft of the transmission and should not be affected by the work that you did. Are the ABS sensors ok?

Apr 02, 2014 | 2001 Ford Windstar

1 Answer

2001 ford windstar the right axle spin slower then the left one. What can be the problem i both two new axle and it stil spin slower then the right but it move better do i need to rebuild the trans


I don't think you can assess the condition of the transaxle by spinning the wheels.
The differential in the transaxle converts power from the transmission to the wheels by a set of gears. It would almost impossible for one side to turn at a different speed than the other.
You may have more drag on the brakes on one wheel, or the fluid in the transaxle could cause one side to go slower with the van off the ground.

Jul 05, 2012 | 2001 Ford Windstar

1 Answer

Whts the torque on the single outer nut on the front axle that holds the wheel bearing hub on a 2001 windstar ?


This is a special nut because it's deformed to retain torque. It's also a one-time use nut. I beleive it is 170-203 ft. lbs, good-day !

Sep 23, 2011 | 2001 Ford Windstar

2 Answers

2001 Ford windstar has a rumble/vibration on left front when driving over speeds of 10 mph. Consstant and increases with speed.


It sounds like you have a bad spindle/hub. You will need to jack up the front left tire, remove the wheel and the brake caliper and pads. Now spin the hub by hand. If you hear a grinding like sounds or low rumble sound, or there is more resistance than normal, replace your hub/spindle assembly.

Jul 06, 2011 | 2001 Ford Windstar

1 Answer

A LOUD hum from the right front while driving a 2001 Windstar. I assume it to b the wheel bearing. Is their another possible reason for this noise?


Could be road noise from a shifted belt in the tire. could be a drive axle going out. those wheel bearings dont hum 99% of the time when they go bad,generally they have a low grinding sound,espesially when you turn,and your teering gets a bit loose and sloppy.
also check to make sure that you dont have a broken strut that may be touching the tire..try putting on your spare and see if that fixex it,if so its a shifted belt in that tire.

May 01, 2010 | 2001 Ford Windstar

1 Answer

Wheel hubs on a 2001 ford windstar 3.8


not sure but you might have to get it machined off and back on

Jun 05, 2009 | 2001 Ford Windstar

2 Answers

Think front wheel bearing is going bad on my 2001 ford windstar van how to tell


Jack up the wheel that may have the bad wheel bearing and position your left or right hand at the top of the wheel and the other hand at the bottom of the wheel and rock from top to bottom if there is over 1 cm of play your wheel bearing needs to be replaced and if there is excesive play from left to right your rack ends need to be gresed if the have a grease nipple or replaced hope i was some help

Jul 28, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2001 Ford Windstar Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...