Question about Ford Cars & Trucks

1 Answer

Have a ford 2n tractor with stripped camshaft gear. no timing mark on crank gear. how to time crank to cam?

Posted by on

  • Bob Ferguson
    Bob Ferguson Dec 09, 2016

    There is no chain, so I guess you mean mesh the
    gears at that point?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 15,467 Answers

Find number one cylinder and bring it to TDC, Rotate the cam till both valves in that cylinder are closed and then hook the chain to the gears. crank it by hand while observing the valves to be sure they are operating normal in respect to intake, compression and exhaust.

Posted on Dec 09, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1966 chrysler 300/383 engine camshaft timing installation procedure with piston @ top dead center compression of #1 cylinder


Cam timing is set to zero on the crank gear, timing mark on gear point directly up to camshaft gear mark.

Sep 28, 2016 | Chrysler Cars & Trucks

2 Answers

Problems of gm


You can rotate the cam/crank into a positon that will not move as you remove the old belt, as long as the new belt places the cam/crank in same position as the old belt had them, it don't matter where the timing marks are. Leave your old belt on, rotate to a position that will not move or have tension on belt, (no matter the marks) and replace the belt. Make sure to recheck timing marks after new belt is installed by rotating the crank/cam back to timing marks, or just trust that the belt was replaced without the cam or crank rotated. Easy off, easy on, just make sure the cam/crank are still in time as the old belt had them located. NOTE: timing marks are there in case of a broke belt, or for a car that has jumped time. As long as cam and crank are held in same positon, and car was in time before the procedure, it don't matter where the timing marks are at during belt replacement.

Dec 15, 2013 | Cars & Trucks

1 Answer

2000 Nissan Frontier 3.3L VG33E engine. Drove it to the store and when i came out it would not start. I determined the timing belt stripped at the crank gear. I replaced the belt. I am pretty certain that...


Nissan markets its D22 and D40 pickup trucks in North America as the Frontier. A six-cylinder 3.3-liter engine with a double overhead camshaft is standard for the D22 models. The timing belt for this engine keeps the camshafts synchronized with the camshaft, enabling the engine to run smoothly. The timing belt has a limited lifetime, and typically requires replacement after 60,000 miles.----------------------------------------------------------------------------------------------
Original Launch CResetter

Mar 06, 2013 | 2000 Nissan Frontier

3 Answers

How to set timing when you relesh tensioner and it changes the alignment postion of pullies 2000 ford ranger 2.5 l


Here is the trick. Align marks. Put the timing belt on the crank shaft pulley first, and after on the overhead cam pulley. Release tensioner and rotate the crank shaft till the timing belt makes two full circles. Try to align marks, you will be at least one tooth off. Align the crank shaft on the mark, and find out how many teeth you are off at the cam shaft pulley. Count the teeth. Remove the timing belt from cam shaft pulley only. Move cam shaft pulley in reverse according to the number of teeth you counted. Make sure the crank shaft pulley is on the mark. Mount the belt at cam shaft pulley.Rotate the belt two circles and check the marks. Repeate this procedure til after releasing the tensioner, and rotating the timing belt two full circles, the mars will be align.

Nov 22, 2010 | 2000 Ford Ranger SuperCab

1 Answer

98 dodge stratus,engine light came on and it died and won't start now.What could be wrong?


when you crank the engine over now, does it sound different than before? if yes, you probably have a broken timing belt. it is also common for the cam gear to slip out of position from the cam and cause an incorrect, but hard to diagnose, timing issue. other no start with check engine light on issues could be a faulty cam or crank sensor.

pull the codes from the vehicles computer. if there is a cam or crank sensor code, or if there is a code that says in some different wording "cam sensor signal does not match crank sensor singal", first check crankshaft to camshaft timing. if belt is ok and timing marks line up then i strongly suggest removing the bolt from the camshaft that holds the cam gear on. with the bolt and cam gear removed you should be able to tell if the cam gear has rotated on the camshaft. there should be a small pin sticking out of the camshaft. if it is broken off then you need to replace the camshaft. if the pin is still there and the timing is good then replace iether the cam or crank sensor depending on what code you have stored in the ecu memory. if the code is not for the cam/crank sensor then google search the code number e.g. "p0502" and your make and model.

Mar 23, 2010 | 1998 Dodge Stratus

1 Answer

No timing mark on camshaft gear 1995 2.2 corsica no. 1 cylinder at tdc.


There's a round mark or hole on the outer edge of both the cam and crank gear, align the cam gear mark at 6 o'clock and the crank gear mark at 12 o'clock so that they meet and your done.Good luck

Feb 25, 2010 | 1996 Chevrolet Corsica

1 Answer

Cant get timing gear off on 1986 f150 with straight 6 gears stripped need to put new one on


af528f2.gif
Removing the camshaft gear from the 6-300

9685a48.gif
Removing the crankshaft gear from the 6-300


7272b65.gif

Installing the camshaft gear on the 6-300


1cfeb37.gif
Installing the crankshaft gear on the 6-300

402ff2b.gif

6-300 timing gear mark alignment


  1. Drain the cooling system and remove the front cover.

CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.


  1. Crank the engine until the timing marks on the camshaft and crankshaft gears are aligned.
  2. Use a gear puller to removal both of the timing gears.
  3. Before installing the timing gears, be sure that the key and spacer are properly installed. Align the gear key way with the key and install the gear on the camshaft. Be sure that the timing marks line up on the camshaft and the crankshaft gears and install the crankshaft gear.
  4. Install the front cover, and assemble the rest of the engine in the reverse order of disassembly. Fill the cooling system.

Jan 10, 2010 | Ford E-150 Cars & Trucks

1 Answer

Timing belt replacement


camshaft timing mark at 12 o"clock, align cam shaft timing mark to ( v ) cut on top of back timing cover, crank shaft gear align 12 o'clock key way up, there will be a mark on the outer edge of gear, on housing at 12 o'clock there will be the timing mark align that mark to crank gear , install belt and your done.Good luck.

Dec 27, 2009 | 1990 Geo Tracker

1 Answer

Need timing marks for 2002 ford explorer 4.0 engine. trying 2 check timing chain. any one know specs


There are no marks on this one. There is a special tool set to align camshafts ($900). The best you can do is to bring #1 cyl to TDC compression with both cam(valve) covers off. #5 cyl should have lobes at equal opening, exhaust just closing and intake just opening.. #1 cyl cam lobes should each be diametrically opposed to the positions of #5. If cams need to be moved, there is no registration of gear onto cam. Just loosen bolt holding gear and move cam. Retighten bolt. Roll thru 2 crank revolutions and check cam timing again.Simple.

Jul 24, 2009 | 2005 Ford Explorer

1 Answer

91 chevy G20


well not sure exactly why it wont line up use something to turn the crank and cam to appropiate position start sliding crank gear until cam gear is touching then start to push both at same time make sure your crank key and cam pin are bothin place On many OHV pushrod engines, the crankshaft sprocket is installed on the crankshaft nose and the crankshaft is rotated to position piston #1 at TDC. At this point, a mark stamped onto the crankshaft sprocket is pointing directly upward (toward the camshaft).
The camshaft sprocket is then temporarily bolted to the cam and used to rotate the cam until a mark stamped on the cam sprocket is pointing directly downward (toward the crankshaft). The sprocket is then removed from the cam (without allowing the cam to rotate).
The timing chain is looped over the cam gear, the mark on the cam gear is positioned directly downward, and the chain is looped around the crankshaft sprocket. When the cam sprocket is attached to the cam, the timing marks on the crank and cam sprockets should be pointing toward one another.

Feb 10, 2009 | 1992 Chevrolet G20

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...