Question about Rover Cars & Trucks

Open Question

How to I remove the balance bar on a Sky Rover Swift RC helicopter?

There seems to be a pin running through the middle that I can't force out.

Posted by on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 80339 Answers

SOURCE: my rc helicopter won't fly just spins like crazy

You have posted this in the wrong product category. Please re-post the question in the correct category.

Posted on Apr 27, 2012


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Alarm system 96 land rover discovery

You can't remove alarms or bypass them, you have to fix them.

Disconnect the battery fully for at least 2 hours.
Hold the negative and positive leads together for 5 minutes.
PUT THE KEY IN THE IGNITION, but not turned on.
Connect the Positive lead to the battery.
Connect the Negative lead in one swift movement.
Wait 15 minutes for the ECM to re-pair the chips in the key and the ignition key.

My mother worked at Land Rover in Solihull for 18 years :>)

Want to bypass your vehicle security system

Nov 16, 2017 | Land Rover Cars & Trucks

1 Answer

Door handle broke

can you open from the inside, its the only way you going to get to sort this, failing that you may need to get a new door card and rip the one off the door at the top corner near to the lock latch and split the plastic and pull the door pin inside to open then take the door card off. sometimes you can do it with out braking the door card but would not say it will not brake. inside there is a plastic clip that the handle go's on then another bar to the lock. this is designed to snap if some one trys to open the door with force.failing that the handle part can snap where the bar fits to it. that you would need to change the handle.

Dec 06, 2013 | Land Rover Cars & Trucks

1 Answer

What is the torque for axle nut 2003 deville

If you mean the big nut in the middle on a front wheel drive vehicle then you just pull it up with the rachet then the long snap on bar and swift sharp push as the bar is in the downward position .That is about the correct the torque ,or about 120lbs

Oct 23, 2012 | 2003 Cadillac Deville

1 Answer

My rc helicopter won't fly just spins like crazy

You have posted this in the wrong product category. Please re-post the question in the correct category.

Apr 27, 2012 | Cars & Trucks

1 Answer

The Serpentine belt keeps walking off the Crank shaft pulley by one rib as if the pulley moved away from the engine.. Is this where the harmonic balancer is. If so, is it difficult to change?

Before you change anything,,check and see if everything is in line..Also feel all the pulleys and make sure everything turns ok...If the powersteering pump has been replaced,,sometimes the pulley was not pressed on far enough..If it seem to be the harmonic balancer make sure its not damage and the bolt in the middle is tight...If you remove it..You remove middle bolt,,then you have to use a puller to remove the harmonic balancer itself..unusuall for the harmonic balancer to be bad unless it was hit by something

Sep 20, 2011 | 2005 Ford Taurus

2 Answers

Ist there a way to start a 1996 range rover without key.

unfotunatley no the newer vehicals do not allow you to do this it is a security feature

Aug 21, 2011 | 1996 Land Rover Range Rover

1 Answer

Where is the crank position sensor in a 1996 Rang Rover P38 4.6? How do you replace the crank position sensor in a 1996 Rang Rover P38 4.6? Thanks In Advance For You Help. Greg

sensor should be next to harmonic balancer.usually bolted to motor.balancer has fins behind it which run through crank sensor magnets to send signals to onboard computer.ensure to replace as per removal method

Feb 28, 2010 | 1996 Land Rover Range Rover

1 Answer

Harmonic balancer

I think that's a 130lb bolt that's propbably going to take even more torque to loosen it. you need a breaker bar on the rright size socket to fit the nut in the middle of the crank. remove the driver tire and all the plastic trim. With the front of the car safely up on jack stands and the hand break applied you should have easy access. Air tools often work best to loosen the nut. but if you need to stop the crank turning to put some serious force on a breaker bar, have a friend put the car in 1st and hold the foot break down as you push the breaker bar towards the back of the car with your foot. you need to lay in front of the car with your legs under it to push against the breaker bar.
If that fails you can wedge the breaker bar against the frame member and do a quick blip on the ignition key to turn the crank. watch out for flying breaker bars though.
putting it back on is just as hard as you need to get up to 130lbs torque to keep in on safely..

Jun 21, 2009 | 1995 Mitsubishi 3000GT

1 Answer

93 suzuki swift runs rough on start

If its equipped with fast idle valve, try to replace it. You may want also to check your TP valve.

Apr 30, 2009 | 1993 Suzuki Swift

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rover Experts


Level 3 Expert

80339 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers


Level 2 Expert

64 Answers

Are you a Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides