Question about Subaru Cars & Trucks

1 Answer

Please give me gasket head tighting torque for subaru vivio 1994 model

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Subaru Master
  • 75,051 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I retorque the head bolts on my subaru forester 2003, I've just recently replaced the head gaskets?


Gaylene Green,


If you already had a heating issue... just skip over all this meaningless RE-Torque "STUFF"

If there was no overheating
before this procedure... I would suggest either the WRONG GASKETS were used... or they were somehow reversed blocking a water passage).

TORQUE has two ways to go...
Too loose = leaks (water and/or combustion)
Too TIGHT = Broken bolt/stripped threads

If it will make you happy

Sure... TIGHTEN... and then RE-TIGHTEN... after running.

That USED to be the way it was done... until they came out with WONDERFUL "Modern" head gaskets... (tighter... never looser... and NEVER (MORE) too tight.

If you think your torque is too much... you MUST also follow the REVERSE torque pattern when loosening (else risk a fractured casting (FOR REALS)).

Although I seriously doubt the desired effect...

The answer is SURE...!! Go for it... Re-Torque...

(Could not possibly hurt... unless you do it wrong!)

Just not sure of the "OVERHEAT" diagnosis...
sounds more than a bit odd.


***
If there is any previous history of overheating... I would pursue that as an INDEPENDANT issue.

Thermostat, defective water pump... radiator cap... or crusted up radiator (any or all of the above + rotten casting plugs in the engine).

Head torque... Naaah.

Mar 01, 2016 | 2003 Subaru Forester

1 Answer

1994 toyota Camry 2.2L. Having problems with Engine after head gasket installation.


Did you use new stretch bolts and the correct torque settings?

Mar 04, 2014 | 1994 Toyota Camry

1 Answer

1989 subaru DL has blown Head Gaskets.


If your not mechanically minded you may find it a challenge, but if you have some nouse then go for it, but remember put back the same way you took it off, you will need a torque wrench to reset the head bolts, not a small job, good luck

Jan 04, 2014 | Subaru Cars & Trucks

1 Answer

Torque specs /head GASKET/2001 cavalier


for the 2.2L OHV:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)

for the 2.4l dohc are as follows:
(pully 9 3 1 5 7
side) 10 6 2 4 8
bolts 1-8 torqued to 65Nm (40ft/lb)
bolts 9-10 torqued to 40Nm (30ft/lb)

then (either engine) give each an additional 90° (¼) turn

it's best to do the tightening in stages, you don't want to go completely tight on the first pass or there will problems and you'll get to do it all over again

May 20, 2010 | 2001 Chevrolet Cavalier

2 Answers

Have changed head gasket etc. as thought was that but on start up to flush engine water was pouring straight out sum. nothing looked wrong in head gasket or intake gasket areas.


where is the watter coming out from? did you follow torque sequence / did you have head resurfaced? check block / did you find any thing wrong with the old head gasket? please give more info, so we can give you better assistance , Thank you for using Fixya.

Apr 10, 2010 | 1988 Subaru Justy

1 Answer

1994 4runner, six cyl. putting rebuilt heads on, toyota head gaskets, new head bolts "tvs 10.9". Torqued bolts in pattern to 33 foot pounds. another 1/4 turn in the pattern. and into my next and final 1/4...


REMOVE 3 BOLTS MAKE SURE YOU HAVE THE RIGHT THREADS.IF BOLTS LOOK OKAY.YOUR BOLTS HOLES HAS DEBRIS OR OIL AND ANTIFREEZE IN THEM.OR YOUR BOLT HOLES IS STRIPPED.YOU HAVE TO REMOVE HEAD TO FIX THE THREAD PROBLEM.IF YOU HAVE NOT MADE THE FINAL TORQUE TO CRUSH AND SEAL HEAD GASKET THE. HEAD GASKET PROBABLY ALRIGHT.YOU HAVE TO LOOSEN HEAD BOLTS IN SEQUENCE BACK OFF A LITTLE AT EACH BOLTS.IF HEAD GASKET LOOK DAMAGE AT BOLT HOLES REPLACE HEAD GASKET.

Nov 13, 2009 | Toyota 4Runner Cars & Trucks

1 Answer

What are the clyinder head bolts torque wrench settings for a 1994 subaru impreza wrx


Impreza torque settings MUST be done in the correct sequence,its critical when re building.
If you have a local garage who are friendly with, ask if they have autodata.If so they can print you a torque sequence and settings.

Nov 10, 2009 | 1996 Subaru Impreza

1 Answer

1994 old cutlass ciera 3100 blown head gasket.


Get a Chilton's book on the car. It will take you thru the whole job, and give you the torque specs for putting it back together. You will need a torque wrench, foot pounds, and a good socket set.

May 04, 2009 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Head torque settings


where ever you get the head gaskets from napa or auto zone they would be able to give you the torque settings can also call them for it

Jan 02, 2009 | Ford E-350 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7727 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...