Question about Cars & Trucks

Open Question

A diagram showing connection of wood beam to foundation wall

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: Fake cedar beam at least I think it is fake is coming loose from ceiling, due to foundation problems.

How much is your life worth? Ignore the structural problem at the risk of your life. Please call a contractor to look at it and give you a free estimate.

Posted on Feb 04, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fake cedar beam at least I think it is fake is coming loose from ceiling, due to foundation problems.


How much is your life worth? Ignore the structural problem at the risk of your life. Please call a contractor to look at it and give you a free estimate.

Feb 04, 2015 | Cars & Trucks

1 Answer

1999 cadillac seville wiring diagram


Check wiring with a test light or volt meter. switch lights to low beam, connect volt meter N probe to a good ground then probe the light socket for the low beam power cable, should show battery voltage, now switch to high beam and test for battery voltage if ok remove the grounded meter probe and probe the cable in the socket that you have not tested this is the ground cable, battery voltage should show if ground cable is ok. If no voltage repair cable ,If voltage present check filament on bulb high beam perhaps the new bulb is faulty.

Jul 10, 2014 | 1999 Cadillac Seville

1 Answer

I need to replace and then adjust the headlights on my 2000 Chrysler 300M. How do I replace the headlights, then adjust them.


Park your vehicle on level ground with the headlights near a garage door or wall. A good distance is 2-3 feet away from the wall or door. The location must be perfectly level and flat at a distance of 10 to 25 feet away from the door or wall.
Switch on the low headlight beams and mark the horizontal and vertical centerlines of each headlight beams on the wall using masking tape. This will mark the center of each beam with a +. The marking will tell you where exactly the headlight beams should be centered from a distance.

Move the vehicle back about 10 to 25 feet away from the garage door or the wall.

Keep the headlights on the low beam setting.
Use the markings you made on the wall or garage door to, check where the light shines and see if the centerlines still match up with the masking tape marks. If the centerlines of the two beams do not align with the tape marks, you can adjust one or both sides as needed.

Make the necessary adjustments with the lights still on while watching the light beams on the wall and your marks.
Turning the top adjusting screws in a clockwise direction will raise the beam while counterclockwise turn will lower it.

Turning the side adjuster screws will adjust the lights to the left or right.

Continue the adjustments until the center of the light beams are aligned with the tape marks. Then adjust the vertical alignment of both beams slightly below the marks on the wall. This will assure that the lights are tilted slightly downward so they won’t blind approaching motorist.

The will align bot lights, the high and low sine both are connected to the same headlight!!

Nov 18, 2009 | 2000 Chrysler 300M

2 Answers

How do you adjust headlights properly for best lighting


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 04, 2009 | 2002 Chevrolet Venture Passanger

2 Answers

Need assistance ,restoring a bed 0n a 1954 1/2 ton chevy


faxonautoliterature lists a build manual for your truck for $30. I bought one for my 82 Chevy and it is a copyof the instructions for each station on the assembly line. Could be exactly what you are looking for. They also have the dealer service manual for under $50. Hope this helps.

Sep 08, 2009 | Chevrolet 3500 Cars & Trucks

1 Answer

Adjusting headlights on 2001 dodge Ram 2500


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jan 19, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

Headlights


well if you have a beam!!! that means fuse are okay if you have a spare bulb try it and see if this gives you back a low beam as well as hi beam if not look under hood in fuse cluster open lid diagram shows witch is the head light relay good place to start.John

Dec 29, 2008 | 2006 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...