Question about Cars & Trucks

Open Question

Were must pipe for wateroutlet be - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Cadillac Deville exaust cross pipe replacement


1) Take it to a muffler shop unless you are a good welder.
2) Procure the new exhaust pipe material.
3) Make the necessary bends in the new pipe to correspond with the layout of the old pipe with a hydraulic tubing bender.
4) Use a band saw to cut the new pipe to lengths using the old pipe as a template.
5) Weld the pieces to form the crossover.
6) Using a cutting torch, cut both exhaust pipes to the length you made the crossover.
7) Weld in the new crossover you just made.
8) If you can't weld with a torch, have no access to a tubing bender and have no way to get the correct exhaust pipe material....take the car to a muffler shop.

Sep 24, 2014 | Cars & Trucks

1 Answer

Convert dual exhaust on 99 sunfire gt to single?


You can cut out the Y pipe and replace it with a flex pipe from parts store, then clamp each end of the flex pipe, the pipe diameter will be 1-7/8 or 2 inch, also for the pipe replacement piece would work from a sunfire or cavalier from 1995 and up, might need to replace the muffler strap too. as it can break from rusting, if not already rusted and broken.

May 28, 2013 | 1995 Pontiac Sunfire

2 Answers

Does it matter what size front exhaust pipe needed to repair 95 toyota avalon


Well, the main point is that it connects to the other two pipes without any leaks.
Also, if the replacement pipe is wider, it could touch other surfaces and damage them from the high heat.

Jul 05, 2012 | 1995 Toyota Avalon

1 Answer

What are the torque specs for 1996 Buick Century 3.1 L intake manifold?


Front Pipe REMOVAL & INSTALLATION Pipe Without Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal..
  2. Raise and support the front of the vehicle on jackstands.
  3. Remove the exhaust pipe-to-manifold nuts.
  4. Support the catalytic converter, then disconnect the pipe from the converter. Remove the pipe.
  5. Remove the exhaust gaskets. To install:
  6. Be sure to use all new gaskets when required. Assemble the system, check the clearance and tighten the bolts to about 15-30 ft. lbs. (20-41 Nm). Fig. 1: Front exhaust pipe connection common on vehicles with the catalytic converter not included 86813320.gif

  7. All clamps should be tightened to about 18-25 ft. lbs. (24-34 Nm). Do overtighten the clamps. If pipes become dented they can leak.
Pipe With Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal.
  2. Raise and support the vehicle.
  3. On some vehicles you will need to remove the brace from the transaxle.
  4. Remove the exhaust pipe nuts from the manifold.
  5. Support the catalytic converter pipe bolts from the rear of the converter.
  6. Lower the catalytic converter/front pipe assembly from the vehicle. To install:
  7. Be sure to use all new gaskets when required.
  8. Attach the new catalytic converter/front pipe assembly to the vehicle. Tighten the pipe to manifold nuts to 20-40 ft. lbs. (27-55 Nm).
  9. Attach the bolts at the rear of the catalytic converter/front pipe. Tighten them to 30-35 ft. lbs. (41-47 Nm).
  10. Connect the brace at the transaxle if removed.
  11. Lower the vehicle. prev.gif next.gif

Dec 18, 2010 | Buick Century Cars & Trucks

1 Answer

How do i chage the fuel injector for a geo metro 1997 LSI?


REMOVAL & INSTALLATION Fig. 1: Removing injectors from fuel rail 84245032.gif
Fig. 2: Make sure injectors rotate freely in cylinder head 84245033.gif
  1. Relieve fuel system pressure and disconnect the negative battery cable.
  2. Remove intake air hose between throttle body and intercooler.
  3. Remove accelerator cable.
  4. Unclamp PCV and fuel return hoses from deliver pipe.
  5. Unclamp injector wiring harness.
  6. Disconnect injector coupler.
  7. Remove cold start injector pipe from delivery pipe.
  8. Remove vacuum hose from pressure regulator.
  9. Remove fuel feed hose from delivery pipe.
  10. Remove pressure regulator from delivery pipe.
  11. Remove delivery pipe with injectors.
  12. Remove injectors from delivery pipe. To install:
  13. Replace injector O-rings and lubricate with fuel. NOTE: Make sure injectors rotate smoothly. If not, probable cause is incorrect installation of O-ring.
  14. Check if insulator is scored or damaged. If it is, replace with new one.
  15. Connect delivery pipe with injectors.
  16. Install pressure regulator to delivery pipe using a new O-ring.
  17. Install fuel feed hose to delivery pipe.
  18. Install vacuum and fuel return hoses to pressure regulator and clamp securely.
  19. Install cold start injector pipe to delivery pipe using new gaskets.
  20. Install injector coupler. Clamp injector wiring harness.
  21. Install PCV hose to cylinder head.
  22. Install throttle position sensor coupler.
  23. Install accelerator cable and adjust free-play.
  24. Install intake air hose to throttle body and intercooler.
  25. Connect the negative battery cable.
  26. Start engine and check for leaks.
prev.gif next.gif

Jul 03, 2010 | 1997 Geo Metro

1 Answer

Coolant leaking on drivers side? have replace resevior and wateroutlet


Sounds very much like a water-pump.

Look for a leak below the water pump.
If so we believe the inter seal of the water pump to be the failure, this will result in a coolant weep coming from the weep hole near the center shaft of the water pump.

RECOMENDATION:
Replace the water pump.

We hope this tip guides to to your solution.

r/
David

Mar 13, 2010 | 2002 Dodge Intrepid

1 Answer

Goes in to four wheel drive but front tires are


Look at the back of the front wheels there is 2 black pipes, 1 for the brakes that conect to the brake unit (callipers) and the other one is the vacume pipe. Most of the time it is damaged. This pipe is softer and thinner than the brake pipe. It will have a inner pipe and outer sleeve (pipe) that is loose from the main pipe, just to prtect the inner pipe. It can have a leak under that sleeve. ENJOY from Willem Potchefstroom SA

Feb 27, 2010 | 1998 Kia Sportage

2 Answers

Need name of pipe


it goes exhaust manifold, head pipe, cat, intermediate pipe, tailpipe

Mar 14, 2009 | 1991 Toyota Tercel

1 Answer

1984 chevy s10 exhaust


No, 2 pipes the same size will not go together. You will need to probably buy an adapter. Lets say you have a pipe 2 1/4 outer diameter "od" " that is measuring from the out side edges across the pipe, you will need a pipe with an inside diameter "id" of 2 1/4 . you get that measurement buy measuring the inside of the pipe. so a pipe with a 2 1/4 od will fit a pipe with 2 1/4 id. .. hope that helps

Best thing to do is take a piece of pipe from the truck and take the cat to the auto parts store and get all the adapters that way. That way you know for sure you got all the right parts.

Feb 20, 2009 | 1984 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...