Question about 1999 Ford Windstar

Open Question

1999 ford windstar engine will not turn over after changing the starter and the battery

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1999 ford windstar sensor problems on 3.8 engine

iac valve is sticking remove valve and clean the shaft so it moves freely. This is a very easy fix.

Posted on Aug 29, 2008

Ad
  • 1 Answer

SOURCE: 1999 ford Windstar

that code is the maf sensor I had the same problem but it went away like yours did only to return a month later. When I was looking this up it seems this is a problem with the winstar

Posted on Oct 27, 2008

lsteward68
  • 331 Answers

SOURCE: 1999 ford windstar won't start,pulling hair out, HELP

remove the negative battery lead fr about ten minutes then reconnect. this will cause the computer to reboot

Posted on Jun 05, 2009

czaa
  • 4525 Answers

SOURCE: 1999 Ford Windstar-Will Turn over but won't start?

fuel pressure regulator could hav failed-located by engine or the ignition module may not be workin-by dist area try not to be a parts replacer-buy a repair book

Posted on Jan 09, 2010

  • 1 Answer

SOURCE: 2000 ford windstar won't start

also check to see if anti theft light is flashing some of them will disingage the starter

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After changing the battery and the starter my 1999 ford windstar engine will not turn over


Make sure solenoid wire it connected and good. Try jumping the battary wires at the solenoid to see if solenoid is bad. The starter should crank when you jump wires if not replace solenoid.

Dec 08, 2016 | Ford Cars & Trucks

1 Answer

Have a 99 ford windstar that wont turn over. New battery, new starter, new alternator. The lights work, door dings it just wont turn over. any ideas?


Is gear stick in park, try starting by earthing starter, then you can trace fault, key start might be problem

Apr 05, 2013 | 1999 Ford Windstar

1 Answer

I have a 1999 ford windstar but it wount start the engine will not turn


is it getting spark , if not then check the fuel system then the starter .it might even be something as simple as your starter relay.

Mar 18, 2010 | 1999 Ford Windstar

1 Answer

1999 Ford Windstar, 3.8 Liter engine. When attempting to start, there is a clunk, but the engine does not move at all. The dash lights dim completely. I tried jumping the battery off another car, allowing...


try replacing the starter motor. can also be the connectors to the battery, starter, or the groundwire connection at the battery or engine block. clean all connections and use dielectric grease on all connections

Mar 15, 2010 | 1999 Ford Windstar

1 Answer

How to replace starter windstar 2003 V6 engine?


2003 Ford Truck Windstar 3.8L SFI 6cyl Repair Guide

Ford Windstar 1999-2003 - Starter Removal & Installation

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
    NOTE When removing the hard shell connector at terminal -S-, grasp the plastic shell. Do not pull on the wire.
  3. Disconnect the starter electrical harness.
  4. Remove the upper starter bolt.
  5. Support the starter and remove the lower bolt.
  6. Remove the starter from the vehicle.

    e1d1735.jpg

  7. Fig. The starter is located at the lower front of the engine, and is visible through the air duct

To install:
  1. Position the starter in the vehicle.
  2. Install the upper and lower bolts. Tighten to 15-20 ft. lbs. (20-27 Nm).
  3. Connect the starter electrical harness. Tighten the starter cable nut to 80-124 inch lbs. (9-14 Nm).
    NOTE When installing the hard shell connector, be careful to push it straight on and make sure it locks in position with a notable click or detent.
  4. Lower the vehicle.
  5. Connect the negative battery cable.

I really hope helps with this (remember rated this help) Good luck.

Dec 31, 2009 | 2003 Ford Windstar

1 Answer

The lights of my 1999 ford windstar minivan work perfectly fine but everything else doesn't. the engine wont turn on whatsoever.


it may be your solenoid which is connected to your starter. You should also check the wires going out of your starter. They could also be frayed.

Oct 31, 2009 | 1999 Ford Windstar

2 Answers

Antitheft wont let engine turn over or start


have you tried disconnecting the battery for 15 -- 30 minutes, it may allow the anti-theft device to reset....

Jul 22, 2009 | 1999 Ford Windstar

Not finding what you are looking for?
1999 Ford Windstar Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...