Question about Acura Cars & Trucks

Open Question

Need a sensor diagram for all on 1997 acura cl

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tony chavous
  • 50 Answers

SOURCE: Find oil filter in engine of acura CL

back side of block under intake if its a 2.2 or a 2.3 if its a 3.0 its on the passenger side of engine bay if you turn the wheel you will be looking at it

Posted on Feb 03, 2009

  • 1 Answer

SOURCE: distributor pinout diagram...

Counterclockwise
Top Left, Yellow
Black
Yelow/Green Stripe
Yellow/ Black Stripe
Black/ Yellow Stripe
Green
Coil as you're facing it, Black/ Yellow Stripe (Left)
Yellow/ Black Stripe (Right)

Posted on May 05, 2009

c17hydro
  • 2984 Answers

SOURCE: how to locate the thermostat for a 1997 acura 2.2

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Locate the thermostat housing by following the upper radiator hose to the engine.
  4. Loosen the hose clamps then carefully detach the hose from the fitting.
If the hose is stuck, carefully use a pick to break the seal between the radiator hose and the housing. If the hose is deteriorated, replace it with a new one.
  1. Disconnect any sensors or switches that may interfere with the removal of the thermostat from the housing.
f163710.gif
Remove the thermostat housing bolts

120abfd.gif
Pull the water outlet neck away from the housing

d9be9b2.gif
Note the installed position of the thermostat, then remove it

  1. Unfasten the retainers, then remove the thermostat housing.
Some coolant may leak out of the housing as the seal is broken.
  1. Remove the thermostat carefully noting how it's installed.
  2. Clean the mating surfaces of the thermostat housing.
Many thermostat housing's are made out of aluminum alloy. A plastic scraper is very effective and will not harm such metals.
To install

1c8dd82.gif

A new gasket must be installed before installation

c732e7b.gif
Install the thermostat with the air bleed valve at the top

  1. Install the new thermostat and gasket.
Install the thermostat with the jiggle pin facing up. This acts as an air bleed and must be at the top of the thermostat to operate properly.
  1. Install the thermostat housing, then tighten the bolts securely.
  2. Connect the radiator hose and tighten the hose clamps securely.
  3. Install any remaining components, then refill the cooling system.
  4. Start and run the engine until it reaches normal operating temperature while checking for leaks.

Posted on Nov 03, 2009

Testimonial: "thank you very much on the solution, didn't take as long as i expected!"

dttech
  • 4803 Answers

SOURCE: show me a diagram where a transmission control

Your transmission is controlled b the same module that controls your engine. It is called the "Powertrain Control Module" It is located in the front passenger floor board. Pull the carpet back from under the dash on the passenger side and you will see it.

Posted on Dec 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Whats code p1156 for acura cl 1998


http://realfsm.com/

FREE ONLINE AUTO MANUALS AND WIRING DIAGRAMS.

Dec 06, 2014 | 1997 Acura CL

1 Answer

O2 sensor po135


Replace sensor

Jul 02, 2014 | 1997 Acura CL

1 Answer

1997 acura cl fuse box diagram


On this website (click link below) you find fuse box diagram and description for Acura CL

Acura CL 2001 fuse box Auto Genius

Oct 18, 2013 | Cars & Trucks

1 Answer

97 Acura CL D4 light flashing


You change the transmission control molcule (TCM).

Jul 26, 2013 | 1997 Acura CL

1 Answer

1997 acura cl abs light is on


One of your wheel hubs/bearings are going bad. This is what your ABS sensor is tied into.

Jan 24, 2013 | 1997 Acura CL

1 Answer

Need help torque ajustmen 1997 acura cl manifol intake


Go out and purchase a copy of the Haynes auto repair manual for the 1997 Acura Cl at your local auto parts dealer. It will have everything you need and then some!

Jan 20, 2013 | 1997 Acura CL

1 Answer

Show me a diagram where a transmission control module is located for a 1997 acura cl


Your transmission is controlled b the same module that controls your engine. It is called the "Powertrain Control Module" It is located in the front passenger floor board. Pull the carpet back from under the dash on the passenger side and you will see it.

Dec 04, 2010 | 1997 Acura CL

1 Answer

I need a diagram of the AC system (specifically the location of the compressor and the condenser) for my 97 Acura 2.2 CL.


The compressor should be between the radiator and the motor, down toward the bottom of the motor, there is a large line and a smaller line connected to it. The condenser is in front of the radiator.

May 11, 2010 | 1997 Acura CL

2 Answers

Check engine light


yes and itys a very common problem yu need to change the speed sensor (VSS) on the trans heres how it comes apart 4359d1c.gif

Feb 21, 2009 | 1997 Acura CL

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...