Question about Acura Cars & Trucks

Open Question

1997 acura cl cooling sensor on radiator location

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 43 Answers

SOURCE: 1997 Acura CL 3.0 Transmission recall

they install an inline filter on one of the cooling lines as part of the recall

Posted on Sep 24, 2008

  • 87 Answers

SOURCE: Reset check engine light

You can do several Things to reset your check engine light. One is to simply pull the positive side of your battery cable off of the battery. Im going to say to just leave it off for about two minutes then place it back on tighten it down and your done. The other way is to bye a check engine light decoder. Are find one from a friend any way it has a reset option on it that will reset it. Ok your welcome good luck and may the force be with you.

Posted on Oct 07, 2008

sheiden9
  • 87 Answers

SOURCE: check engine light

yes and itys a very common problem yu need to change the speed sensor (VSS) on the trans heres how it comes apart 4359d1c.gif

Posted on Apr 04, 2009

keithheavili
  • 410 Answers

SOURCE: transmission dipstick location

Sorry, I'm just now getting it to you.  The dipstick is located on the passenger side of the car way down at the bottom.  It should have a yellow handle.  It's just to the right and down of the battery.  Let me know if you can't find it still and I will get you a picture somehow.

Posted on May 17, 2009

  • 2 Answers

SOURCE: cooling fan switch/or sensor

The Coolant temp Sensor is located right under the top radiator hose (on the engine side), with a little black connector!, You might have to remove th etop hose to get to it with a deep socket and extension!.
Also Dont Forget to blled the coolant system by the bleeder valve uptop right near/above the coolant sensor!.(10MM Mini socket w/ extension IIRC!)

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is a 1997 Acura 2.2 cl coolant temperature sensor located?


Hello Alisa A Floyd,

Generally located on the engine ide of the
TOP RADIATOR HOSE...

Could be one or two wires... (catalog shows BOTH)

I will attempt to give you a ROCK
AUTO picture so you can see what you are looking to FIND.

Hope this helps.

1997 ACURA CL 2 2L L4 Temperature Sender Sensor RockAuto

Nov 26, 2016 | Acura Cars & Trucks

1 Answer

How to locate thermostat on 1997 acura cl 3.0


that big hose in the RAD goes to it.
just follow that hose.. and bingo.

here , i log in to alldata.com
step three
  1. Locate the thermostat housing by following the upper radiator hose to the engine.

Nov 19, 2013 | 1997 Acura CL

1 Answer

I have a 1997 acura cl 3.0 everytime i turn off my car the cooling fan stays on for quite awhile


The cooling fan is controlled by a heat sensor and operates independently of the motor. When you turn off your Acura, the cooling fan continues to run until the sensor determines the tempurature has decreased enough to turn off the fan

Dec 24, 2012 | 1998 Acura CL

1 Answer

I need a diagram of the AC system (specifically the location of the compressor and the condenser) for my 97 Acura 2.2 CL.


The compressor should be between the radiator and the motor, down toward the bottom of the motor, there is a large line and a smaller line connected to it. The condenser is in front of the radiator.

May 11, 2010 | 1997 Acura CL

1 Answer

97 2.2 cl high idle, self rev, overheat, started same time


i cannot specifically point out what the problem might be, but an overheating car---never a good thing. check everything related to cooling. fans, radiator, hoses, waterpump, coolant overflow tank(see if its got a brownish color or looks like there is oil), and check your oil while your at it...

Jan 17, 2010 | 1997 Acura CL

1 Answer

How to locate the thermostat for a 1997 acura 2.2


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Locate the thermostat housing by following the upper radiator hose to the engine.
  4. Loosen the hose clamps then carefully detach the hose from the fitting.
If the hose is stuck, carefully use a pick to break the seal between the radiator hose and the housing. If the hose is deteriorated, replace it with a new one.
  1. Disconnect any sensors or switches that may interfere with the removal of the thermostat from the housing.
f163710.gif
Remove the thermostat housing bolts

120abfd.gif
Pull the water outlet neck away from the housing

d9be9b2.gif
Note the installed position of the thermostat, then remove it

  1. Unfasten the retainers, then remove the thermostat housing.
Some coolant may leak out of the housing as the seal is broken.
  1. Remove the thermostat carefully noting how it's installed.
  2. Clean the mating surfaces of the thermostat housing.
Many thermostat housing's are made out of aluminum alloy. A plastic scraper is very effective and will not harm such metals.
To install

1c8dd82.gif

A new gasket must be installed before installation

c732e7b.gif
Install the thermostat with the air bleed valve at the top

  1. Install the new thermostat and gasket.
Install the thermostat with the jiggle pin facing up. This acts as an air bleed and must be at the top of the thermostat to operate properly.
  1. Install the thermostat housing, then tighten the bolts securely.
  2. Connect the radiator hose and tighten the hose clamps securely.
  3. Install any remaining components, then refill the cooling system.
  4. Start and run the engine until it reaches normal operating temperature while checking for leaks.

Nov 03, 2009 | 1997 Acura CL

2 Answers

1998 Acura 2.3 CL radiator fan too loud


The sensor is being sensitive. When you come to a stop,after high speed, the temp can spike and trip the sensor. Not unusual. If you have the ac on it will kick the fan into high speed as well. not unusual.

May 29, 2009 | 1998 Acura CL

1 Answer

1999 Acura CL - Gas Filter


4cyl and 6cyl are both located on the firewall, driver side under the hood

Oct 28, 2008 | 1997 Acura CL

2 Answers

1997 Acura CL 3.0 Transmission recall


they install an inline filter on one of the cooling lines as part of the recall

Sep 24, 2008 | 1997 Acura CL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...