Question about Ford Cars & Trucks

Open Question

I have a 1985 Ford Ranger p.u. with a 2.3 Mitsibushi diesel engine.Is there a spacer plate between the starter & bellhousing

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the camshaft cap bolt tentions on a 2007 ford ranger 3.0 turbo diesel common rail engine


I looked at info for 99 ford ranger 3.0L engine.
The thrust plate on end of camshaft, the torques for those bolts, 84 inch lbs.
If I misunderstood your post, please excuse?

Nov 04, 2016 | Ford Cars & Trucks

1 Answer

Where do the fuel lines go on a 1985 ford ranger?


From the fuel tank along the driver side frame rail up to the engine.

Sep 12, 2015 | 1985 Ford Ranger

1 Answer

How do you get a starter out of the engine bay on a pk 09 ranger


best removed from underneath. disconnect battery first. remove wiring at starter and 3 bolts holding it to bellhousing.

Apr 14, 2015 | Ford Ranger Cars & Trucks

1 Answer

Where is the crankshaft position sensor on a 2003 jeep grand cherokee laredo located V6 4.0


The Crankshaft Position Sensor (CKP) is mounted to the transmission bellhousing at the left/rear side of the engine block...

9_21_2011_12_48_19_pm.jpg


9_21_2011_12_48_47_pm.gif

Inatallation: 4.0L Engine
New replacement sensors will be equipped with a paper spacer glued to bottom of sensor. If installing (returning) a used sensor to vehicle, a new paper spacer must be installed to bottom of sensor. This spacer will be ground off the first time engine is started. If spacer is not used, sensor will be broken the first time engine is started.

New Sensors:
Be sure paper spacer is installed to bottom of sensor. If not, obtain spacer PN05252229.

Used Sensors:
Clean bottom of sensor and install spacer PN05252229.
  1. Install sensor into transmission bellhousing hole.
  2. Position sensor wire shield to sensor.
  3. Push sensor against flywheel/drive plate. With sensor pushed against flywheel/drive plate, tighten mounting bolt to 7 Nm (60 inch lbs.) torque.
  4. Route sensor wiring harness into wire shield.
  5. Connect sensor pigtail harness electrical connector to main wiring harness.
Hope helps (remember to rate and comment this free answer).

Sep 06, 2011 | 2003 Jeep Grand Cherokee

1 Answer

I have a code P320 on my 1999 Jeep Grand. What do I need to replace and how? Thanks for your help. John


Replace the crank sensor.


360dreamworx_25.gif
The Crankshaft Position (CKP) sensor is mounted to the transmission bellhousing at the left/rear side of the engine block. The sensor is adjustable and is attached with one bolt. A wire shield/router is attached to the sensor.

REMOVAL
  1. Disconnect sensor pigtail harness (3-way connector) from main engine wiring harness.
  2. Remove sensor mounting bolt.
  3. Remove wire shield and sensor.
INSTALLATION
New replacement sensors will be equipped with a paper spacer glued to bottom of sensor. If installing (returning) a used sensor to vehicle, a new paper spacer must be installed to bottom of sensor. This spacer will be ground off the first time engine is started. If spacer is not used, sensor will be broken the first time engine is started.
  1. New Sensors: Be sure paper spacer is installed to bottom of sensor. If not, obtain spacer PN05252229.
  2. Used Sensors: Clean bottom of sensor and install spacer PN05252229.
  3. Install sensor into transmission bellhousing hole.
  4. Position sensor wire shield to sensor.
  5. Push sensor against flywheel/drive plate. With sensor pushed against flywheel/drive plate, tighten mounting bolt to 7 Nm (60 in. lbs.) torque.
  6. Route sensor wiring harness into wire shield.
  7. Connect sensor pigtail harness electrical connector to main wiring harness.

Jul 12, 2011 | 1999 Jeep Grand Cherokee

1 Answer

Removing starter 98 plymouth voyager 3.3


3.3L & 3.8L Engines To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the wiring from the starter and starter solenoid.
  4. Remove the starter mounting bolts.
  5. Remove the starter and spacer from the bellhousing.
To Install:
Starter motor removal/installation (3.3L & 3.8L engines) chry-02-33-788.gif

  1. Place starter spacer in position on bellhousing, make sure flange is toward flywheel.
  2. Place starter in position on bellhousing.
  3. Install the mounting bolts and ground wire. Tighten the bolts to 40 ft. lb. (54 Nm).
  4. Connect the wiring to the starter and solenoid.
  5. Lower vehicle.
  6. Connect the negative battery cable.
  7. Verify correct starter operation.
prev.gif next.gif

Oct 13, 2010 | 1998 Plymouth Voyager

2 Answers

Ford Ranger 2.5 on a53 plate. EML comes on


my ford ranger run rought when i rare it up it blows some black smoke

Oct 12, 2009 | 2003 Ford Ranger Regular Cab

2 Answers

Replaced starter and relay and battery now when I try to start it will not disengage from the flywheel any help would be appreciated thank you


itz always gud tagit other opinions before operating-or ull become a parts replacer n daats$$$-i think lookin at the ignition switch may help unless u hav the relay n soleniod thats bad or hooked up rong

Aug 18, 2009 | 1994 Ford Ranger Supercab

1 Answer

1985 ford 250 diesel - Starter verese Battery


Both batteries need to be fully charged. Some have solinoids on both the starter and the fender well. Don't use ether in that engine. It can cause engine damage.

Jan 07, 2009 | 1985 Ford F 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...