Question about 1997 Pontiac Grand Am

Open Question

Where is the voltage regulator located at on a 1997 Pontiac Grand Am

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 1997 pontiac grand am

junk it

Posted on Sep 12, 2008

  • 743 Answers

SOURCE: 1990 dodge caravan voltage regulator location

The Voltage regulator is in the PCM.

Posted on Sep 30, 2008

  • 740 Answers

SOURCE: Voltage regulator on 1985 Toyota Supra

It's built in the alternator.

Posted on Jan 05, 2009

ZJLimited
  • 17970 Answers

SOURCE: how to change a fuel pressure regulator in a 1997

GM Century/Lumina/Grand Prix/Intrigue 1997-2000
Fuel Pressure Regulator - Removal & Installing

The fuel pressure regulator is a diaphragm-operated relief valve with fuel pump pressure on one side and regulator spring pressure and intake manifold vacuum on the other side. The regulator's function is to maintain a constant fuel pressure across the injectors at all times. The pressure regulator compensates for engine load by increasing fuel pressure as engine vacuum drops.

The fuel pressure regulator is serviced as a separate component. When servicing the pressure regulator, make sure that the O-ring back-up, large O-ring, filter screen and small O-ring are properly positioned on the pressure regulator.


44dcbf8.jpg Fig. Cutaway view of a typical fuel pressure regulator


REMOVAL & INSTALLATION
The need to work as cleanly as possible cannot be over-emphasized. Even the smallest amount of dirt, if allowed into the fuel pressure regulator and/or the fuel rail, will find its way to the fuel injectors. The nozzle openings of the injectors are very small. Keep hands and tools clean. Clean the areas to be disconnected with a suitable solvent. Carefully cover open fittings and connections to keep out foreign material. Dirt in the injectors almost guarantees a clogged fuel injector and engine performance problems.
3.1L and 3.4L (VIN E) Engines

  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure using the procedures found in this section.
  3. Remove the upper intake manifold assembly. Please see .
  4. Disconnect the vacuum line from the pressure regulator.
  5. Remove the regulator retaining screw and remove the retainer bracket. Using a clean shop cloth to catch fuel spillage, carefully pull the regulator from the fuel rail. Twist the regulator slightly while removing to ease removal. Discard the O-ring.

4ecb713.jpg

Fig. Exploded view of the fuel pressure regulator mounting-3.1L and 3.4L (VIN E) engines
To install:
  1. Clean all parts well. DO NOT use shop compressed air to test or clean a fuel pressure regulator. Clean the fuel pressure regulator screen, if necessary. DO NOT immerse the fuel pressure regulator in a solvent bath or it will be damaged.
  2. If the filter screen has been contaminated, it should be removed and the pressure regulator replaced.
  3. Lubricate a new pressure regulator O-ring with clean engine oil and install on the regulator inlet.
  4. Install the fuel return pipe to the regulator.
  5. Install a new retainer and spacer bracket into the slot on the fuel rail and install the pressure regulator to the fuel rail. Tighten the fuel return line nut to 13 ft. lbs. (17 Nm).
  6. Connect the vacuum line to the pressure regulator and install the retainer screw. Tighten to 76 inch lbs. (8.5 Nm).
  7. Inspect and verify that the retainer and spacer bracket is engaged in the slots in the fuel rail. Grasp and pull on the regulator to ensure that it is properly seated.
  8. Install the upper intake manifold. Please see .
  9. Connect the negative battery cable.
  10. Inspect for leaks using the following procedure:
    • Turn the ignition switch to the ON position for 2 seconds.
    • Turn the ignition switch to the OFF position for 10 seconds.
    • Turn the ignition switch to the ON position again.
    • Inspect all areas for fuel leaks.

Other size engine can find in autozone.com (free register).

Hope this help (remember rated this).

Posted on Feb 08, 2010

samtoler
  • 666 Answers

SOURCE: wHERE IS MY FUEL PRESSURE REGULATOR LOCATED ON MY

On the fuel rail on the engine

Posted on Jun 14, 2010

Testimonial: "thanks a bunch, i appreciate it!!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove intake manifold for 1997 pontiac grand prix


You have to remove anything that is connected and in the way of the intake. Remove the fuel rail, the EGR valve and supply pipe from the manifold, the map sensor, the vacuum for the fuel pressure regulator, the alternator and support bracket, the water pipes for the throttle body, and the bolts that hold it down.

Jun 09, 2015 | 1997 Pontiac Grand Prix

1 Answer

Battery keeps dying in 1997 Pontiac Grand AM. I've


There is a voltage draw from your battery while engine is not running.to prove this loose any one of your terminals.with all switches turned off including engine, disconnect and re-connect the loose terminal.if you get a spark then there is a voltage draw, find the wire and replace it

Feb 04, 2012 | 1997 Pontiac Grand Am

1 Answer

Passenger front window regulator whirs but does not move the window pontiac grand prix 1997


the window regulator is broken. buy one from the dealer. Aftermarket ones don't last very long.

Sep 07, 2011 | 1997 Pontiac Grand Prix

1 Answer

Location of the airbags fuses in 1997 Pontiac Grand prix


Check in the Fuse Block (undehood) passenger side, with ths SIR label (Supplemental Inflatable Restraint)

d9e71d2.gif

Also check the 1997-Pontiac-Grand-Prix-Owners-Manual (page 339 and next).

Good luck; remember rated this post.

Apr 09, 2010 | 1997 Pontiac Grand Prix

1 Answer

The main RED lead off the back of the altenator should I get the full output of voltage when checking with an amp meter?


Hi,
The alternator has a built in regulator. The out put will be highest when you first start your car, As the regulator senses the battery is getting charged it will reduce the amps until it stabilizes between 13.5 and 14 volts. This is off the red positive post you spoke of.

Mar 28, 2010 | 1997 Pontiac Grand Prix

2 Answers

I HAVE 1997 PONTIAC GRAND PRIX SE WITH 3.8 IT WILL START BUT AFTER A FEW SECONDS WILL SHUT OFF


i would start with fuel pressure test first to see if pressure is constant or fades,,

Feb 18, 2010 | 1997 Pontiac Grand Prix

2 Answers

Voltage regulator location on 1994 Bonneville


Usually they are on the firewall or wheelwell, inside the engine compartment.

Nov 10, 2009 | 1994 Pontiac Bonneville

Not finding what you are looking for?
1997 Pontiac Grand Am Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...