Question about Cars & Trucks

Open Question

Have a 648g skidder that the park light is on and machine won't move. Gear selector moves freely in forward and reverse.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Car wont move.

Could be that your linkage is broken and just looks like it is shifting or a bad tranny module or tranny but i would look at the linkage and see if it is hooked up to the tranny.

Posted on Oct 10, 2008

Ad
  • 57 Answers

SOURCE: sprinter gear selector

This is the gear linkages. It is a cable operated system to allow the gear lever to be dash mounted.

They are a common fault. The parts are about £65 from Mercedes (dealer only part) and unless you know what you are doing you can expect about 2 - 3 hours labour charge, though there are no special tools involved.

They average about 60,000 miles, though the replacements tend to be better.

Posted on Mar 28, 2009

  • 521 Answers

SOURCE: I have a 1999 Cadillac Esclade,Automatic Transmission

internal transmission problem. Unless you know how to rebuild a transmission it is best to take the dealr or a transission repair shop like AAMCO.

Posted on Jul 18, 2009

dmsr63
  • 2050 Answers

SOURCE: gear select lever is very loose. It move forward

There is a pin that goes through the shifter that hold it in place, along with a spring just inside where the end of the shifting lever is, that makes the lever "return" after you pull it back to shift. These springs can break and bind up. Take a look at both.

Posted on Aug 14, 2009

  • 2 Answers

SOURCE: My gear shifter won't move out of park on my 2006

http://www.custombilletstore.com/produc
t_p/1028.htm


This problem also happened to me. However, I found the part online that replaces the second pink lever. The new part is made of metal so the part will never break again. I made the emergency fix with the dremel, ordered the part, and a week later the part came. I am making the permanent fix today. Follow the link above to order the new part. It costs around 49.00 including tax and shipping. It will take you appx 2 hours to remove the shifter, change the part, and reinstall.

Posted on Sep 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

50 horse 4 stwont go into reverse gear due to shaft problems


the drive shaft just drives a pinion gear in the prop box that drives to gears that spin in opposite directions all the time
by selecting forward with the selector rod , a dog gear is moved forward to mesh with one gear that is turning or moves the other way to engage the other gear that is turning
that is the forward or reverse action for the prop
if you have forward but no reverse the it is not a drive shaft problem but a selector rod adjustment that is not moving the dog far enough to engage the running gear

Jul 08, 2017 | Cars & Trucks

1 Answer

How do I fix the transmission problem? The car is moving forward at neutral, drive and low gear, and switching to parking mode at reverse and parking. The car is not backing up at all.


Transmission may now be toast since you continued to drive it when maybe low on fluid or torque converter had failed. How long since last fluid and filter change? Ever?

Jul 19, 2015 | 1992 Lincoln Town Car

1 Answer

My smart fortwo will not engage automatic or reverse


If the ABS has a problem , the transmission will not work properly

Mar 30, 2015 | Smart Cars & Trucks

1 Answer

Why wont my 1986 f250 auto ****** not go into rev. or park


it sounds like you reconnected the linkage in the wrong position so it can still go into the forward gears but there is not enough cable length to allow for reverse and park to be engaged disconnect the linkage again and use trial and error to get it back to where you need it also the linkage should show you where the bolt was that tightened it but if you took it off and then moved either the linkage or the transmission gear selector arm on the transmission now its not in the position it was when you disconnected it resulting in this problem of no access to the other shifter points park reverse and you will have to check all gear shifts till you get it right but if it was in park when you took it off take the linkage off move the trans gear selector to park and reconnect it where the old marks are and you should be O.K.LATER MAN!

Aug 21, 2014 | Cars & Trucks

1 Answer

Car won't turn


try to change you car battery and then shift to park and try to start the engine if that didint help contact me on ahmadamere_2000@yahoo.com i will help you to get it back agian

Nov 24, 2013 | 1999 Jeep Wrangler

1 Answer

The gear selector on my 2002 Ford Windstar moves, but the transmission won't go into gear. Why is the transmission not going into gear?


try to replace transmission strainer first torque convertor and see if that helps if not it probabaly the transmission

Jan 31, 2013 | Cars & Trucks

2 Answers

My 2004 chevy cavalier won't start it is stuck in


Your shifter cable sounds like it separated from the transmission or shifter or just broke. you are probably stuck in a moving gear so the neutral safety switch is disabling the ignition.

Jan 07, 2012 | 2004 Chevrolet Cavalier

1 Answer

My 1999 Pontiac Sunfire GT 2.4L Automatic Gear Selector is broken


you car likely thinks its stuck in reverse, which it may be... even if you can roll it. you'll need to find a way to either get it into park or neutral, normally this can be done by the actual linkages under the shift console or from underneath the car.

Apr 07, 2017 | 1999 Pontiac Sunfire

1 Answer

Whining from engine when in gear


Just a thought- remove the oil filler cap when the whine is present - (this checks if PCV valve is faulty, causing high crankcase vacuum, which in turn causes a whistling/whine noise as air leaks past engine oil seals). Worth a check.

Try listening with a short piece of hose pipe to locate immediate area/source of noise.

Jun 17, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

Jetta 2003 6 speed manual transmission problems


There is small chance you problem is with the slave cylinder, or the clutch master cylinder.
Check the brake fluid under the hood in the clutch master cylinder. If it is gone, or low, you may be leaking brake fluid either from the slave cylinder on the transmission, or the fluid could be bypassing the rubber seals inside the master cylinder.
I hope this is what is wrong, as it is much less expensive than having the transmission repaired.
God bless your efforts.

Apr 18, 2017 | 2003 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...