Question about 1998 Oldsmobile Cutlass

Open Question

I put a turn signal switch/horn in a 98 cutlass from a similar year Malibu. Turn signals work horn won't shut off. I left the screw out so its not making contact, switch's work but need horn. Ideas?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76673 Answers

SOURCE: Turn signals flashing rapidly

This fast flash is caused by a burnt out bulb in the front or rear.

Posted on Nov 06, 2008

Ad

SOURCE: turn signal not flashing

Most likely cause is the flasher relay located under the drivers dash in the fuse panel. This relay is round and may be metal. Replace it with an electronic flasher relay. Pay the ten bucks and have trouble free service for a lifetime.....
Good Luck.
Philip

Posted on Jan 26, 2009

  • 1 Answer

SOURCE: I need to locate and replace the multi function switch

My turn signal flasher was located to the right of the ash tray, I looked around the column for HOURS and it wasn't there... I also have an 93 oldsmobile cutlass ciera, it drove me crazy because the manual wasn't correct.

Posted on Mar 22, 2009

dburns60
  • 410 Answers

SOURCE: I need to replace turn signal switch on 97 olds cutlass supreme.

Disconnect the battery to do any service on the steering column or front radiator areas.

Posted on Jun 30, 2009

  • 1 Answer

SOURCE: where is the turn signal flasher on a 1993 olds

If not in fuse panel, take ash tray out, unscrew ash tray assembly and pull out. The flasher is on the right side of the ash tray right up front.

Posted on Nov 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the turn signal relay on a 2004 Malibu lt, and do you know what would cause the front turn signal lites to work then not work then work then not work?


There isn't one. Since you already did the fuses. If your up to it. Take the turn signal switch out. Take it apart and fix it, the inside of it.. You need a soldering gun and solder. There is only one thing that may op out. The horn spring. Plus the button for the horn will drop,out. Just look at the contacts and solder them up( divots have to be filled in). Plastic will melt. just watch. it works. Fixed a lot of them. You can do it...You already passed the first step..

Dec 04, 2014 | 2004 Chevrolet Malibu

1 Answer

How would I go about replacing the turn signal switch on a 92 Cutlass Supreme S?


Well two major tools you will need,a steering wheel puller ,and a lock plate remover.Remove the horn button(carefully disconnect the horn button wire) pad,screws on back side of steering wheel,then remove large nut holding steering wheel(but first mark steering wheel to be sure you are able to line it back up properly),then use the steering wheel puller,after steering wheel is removed install lock plate remover and compress lock plate down ,and remove C clip pull upwards out of groove,remove puller and C clip and remove horn rotor and lock plate,and you are at the turn signal switch three screws hold the part,remove emergency switch with phillups screw driver and the turn signal lever. remove bezel under dash (where ur knees would be,and disconnect the long flat plug and remove it from its holder and remove turn signal switch.

Oct 25, 2013 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

Left turn signal won't work when cold. If I put on signal and hazards then turn hazards off the signal will work. How do I fix this?


depending on year,and model.... i would inspect hazard switch. if not a bad switch,a poor connection would be what i would look for.

Sep 16, 2011 | Pontiac Montana Cars & Trucks

1 Answer

My left rear turn signal is out on my 2006 Malibu. The bulb is good, but I replaced it anyway since I had the assembly apart. The left front flasher works fine as well. Before I try and replace any...


Stop lamp an hazard lights work ?
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.

Repair an open, high resistance, or short to ground in the inoperative turn signal supply voltage circuit. Refer to Circuit Testing and Wiring Repairs .
Did you complete the repair?

May 16, 2017 | 2006 Chevrolet Malibu

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

1 Answer

2001 Malibu - turn signal & horn problems


Google Service Bulletin No. 04098A. There is a recall for the hazard switch. My car's vin is not within the range, but I have the blinker problem. I was told by the Chev. 800 number that if a dealer determines that is the problem they will replace it. You can also buy the switch for about $20 and replace it yourself if you don't want to have to deal with a service dept.

Sep 23, 2009 | 2000 Chevrolet Malibu

1 Answer

Left turn signa on 1999 malibu does not work when


I need more detail, but look in to the turn signal switch. it controls head lights turn signals ect.

Sep 04, 2009 | 1999 Chevrolet Malibu

2 Answers

Turn signal keep clicking randomly 03 malibu


To diagnose: Does the clicking resume to normal when the turn signal or hazrds on? Then:
Multi function switch is damaged.(seems to be common) This unit consists of the two control arms(turn signals and wiper control) on either side of the steering column. It is easily replaced. Cost, app. 200 from GM or 160 aftermarket. GM product is TRW assembled in Mexico. Aftermarket is made in Taiwan. Firstly:

Disconnect battery.

There are 3 #20 Torx screws under the steering column shroud. Remove them and carefully separate shroud and remove. It takes a bit to worm the shroud around the column tilt lever. I didn't check but you may not even have to remove the lower section.

There is 1 #20 torx screw on top holding the MFS in place. It also has 2 guide pins on the bottom. Remove the screw and disconnect the 3 electrical pin connectors. Now remove and replace with new unit. I did notice the steel pin that operates the horn(it pushes in and out and sits against a rotating plate in front of the steering wheel) was a bit rough so I smoothed it out with a small file. Now put everything back in place.

Anyway, that should take care of the clicking. It worked for me.
rough so I smoothed it out with a small file. Now put everything back in place. Anyway, that should take care of the clicking. It worked for me.

Jun 27, 2009 | 2003 Chevrolet Malibu

Not finding what you are looking for?
1998 Oldsmobile Cutlass Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...