Question about 2011 Chevrolet Cruze
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
CAUTION: During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT overtighten bolt No.11.
Posted on Apr 21, 2010
99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.
Posted on Sep 07, 2010
well according to my alldata book its 30nm then slacken 90? and tighten again 90? ,---Well in all honesty i cannot see this being done on a assembly line at three engines a minute where they are pulled down at once with one big air driven socket machine so here what i would do and its old school in fact it may even be older than me which i doubt ,anyway all jokes aside i would pull down first with a rachet in sequence and this invoilves the first bolt in the middle then the one above it then do one each side alternativly easy so you start in the middle and work your way out left then right left then right and so on ,after pulling them down with a rachet this will apply about 30/35lbs ,then use the breaker bar and pull them down again till i feel it stretch the bolts but as your not me you do as i say not as i do ,so set torque wrench to 55lbs and pull them down in order again ,then coffee break and thats compulsory now up the setting to 65lbs and pull them down again and that should do you ,you should not need to pull them down after so many miles this is not a 1959 morris a series engine but a VW state of the art piece of kit
Posted on Feb 17, 2011
if the 8th number om your VIN is a "J" then this is the correct prossess 3.1LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.
if the 8th number on your VIN is a "M" then this is the correct prossess 3.8LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.
Posted on Nov 07, 2011
Go to this LINK for the info in pdf format, the sequence is on page 16 of the pdf file.
Posted on Feb 16, 2012
Testimonial: "Great help...just the info I needed to do job. Thankyou very much."
Tips for a great answer:
Jan 23, 2018 | Cars & Trucks
Dec 13, 2016 | 2011 Chevrolet Cruze
Dec 10, 2016 | 2011 Chevrolet Cruze
Sep 24, 2015 | 2012 Chevrolet Chevrolet Cruze LT
Jul 22, 2015 | Daihatsu Rocky Cars & Trucks
Jul 17, 2015 | 2011 Chevrolet Chevrolet Cruze ECO
Aug 06, 2014 | 2011 Chevrolet Cruze
Mar 28, 2013 | 2011 Chevrolet Cruze
Apr 21, 2010 | 1998 Jeep Cherokee
Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme
Oct 11, 2017 | 2011 Chevrolet Cruze
210 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: