Question about Cars & Trucks

Open Question

I have a 1999 international box truck 22 ft the bolt holder for the box has been broken. Can someone out there give me an answer to able to fix it myself. Thank you

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22219 Answers

SOURCE: Broken Bolt In Front of Engine

lower altenator support bracket bolt ,doubt if its broke just needs retightening

Posted on Jan 08, 2009

Ad
oilyspill
  • 3657 Answers

SOURCE: 3.9l V6. Can I re-torque rear caliper bolts to 26 ft. lbs.?

I agree with Bill.
My info for rear caliper bolts says 32 ft lbs on your vehicle. Just leave it alone.

Posted on Mar 02, 2016

  • 44530 Answers

SOURCE: Neil Williams8 minutes ago I was told to tighten the front caliper bolts to 26 ft. lb. and the bracket to 133 ft. lb.194,000 miles on odometer. Is this correct?

I would go with the Utube advice as the bolts in use will probably shear off at 133 ft/lbs
40 ft/lbs for the calliper bolts and 70 ft/lbs is more in the region of being correct
follow the specifications in the workshop manual or get advice from a specialist brake shop as to the required tension b for the bolts

Posted on Mar 25, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs and sequence for the intake and head gasket on a 1999 Chevy Silverado 6.0l V8 K2500


Cylinder Head Bolts (First Pass all M11 Bolts in Sequence)
30 N?·m
22 lb ft
Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence)
90 degrees
Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head)
90 degrees
Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence)
50 degrees
Cylinder Head Bolts (M8 Inner Bolts in Sequence)
30 N?·m
22 lb ft
Intake Manifold Bolts (First Pass in Sequence)
5 N?·m
44 lb in
Intake Manifold Bolts (Final Pass in Sequence)
10 N?·m
89 lb in
Intake Manifold Wiring Harness Stud
10 N?·m
89 lb in

Oct 27, 2015 | Cars & Trucks

1 Answer

What are the big end torque settings for a Daewoo matiz 800


main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs.

Nov 29, 2014 | 1999 Daewoo Matiz

1 Answer

What r the torque specifications on installing a head on 2000 sierra 5.3 and the tightening sequence


You must use new bolts, failure to do so will result in redoing the job.

Tightening sequences
intakes side 15 13 11 12 14
center 10 3 1 5 9
exhaust side 7 6 2 4 8

Step 1
all 11mm bolts 22 ft lbs
Step 2
all 11mm bolts turn add 90deg
Step 3
11mm bolts 1-8 turn add 90 deg
11mm bolts 9 and 10 turn add 50deg
Step 4
all 8mm bolts 22 ft lbs

Oct 24, 2012 | 1999 GMC Yukon Denali

1 Answer

Show picture of how to put alternator on 2.2 s10


This answer is in a previous question; just keep in mind this procedure to install:
  1. Position the alternator in the vehicle and loosely install the retaining bolts.
  2. On 1994-98 models, tighten the top alternator bolt to 22 ft. lbs. (30 Nm) and the bottom bolt to 32 ft. lbs. (43 Nm).
  3. On 1999-99 models, tighten the rear bolt to 37 ft. lbs. (50 Nm) and the front bolt to 18 ft. lbs. (25 Nm).
  4. On 1994-98 models, install the alternator brace, then tighten the retaining nut(s) and bolts to 22 ft. lbs. (30 Nm).
  5. On 1999-99 models, install the alternator brace, tighten the brace-to-alternator and brace-to-intake retainers to 18 ft. lbs. (25 Nm). Tighten the brace-to-engine stud nut to 37 ft. lbs. (50 Nm).
  6. Install the battery terminal wire and tighten the retaining nut, then engage the alternator wiring connector.
  7. Hold the serpentine drive belt tensioner, back off the belt while slipping the belt over the alternator pulley. Gradually lower the tensioner into contact with the belt, then check for proper alignment and tension.
  8. Connect the negative battery cable.





Previous question link HERE.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 21, 2012 | Cars & Trucks

1 Answer

What is the torque setting for 1999 ford 182 exaust manifold


Check this for 1996-1999 FORD 3.0L (182) V6 DOHC...
- Install the exhaust manifold with a new exhaust manifold gasket.
- Install the exhaust manifold retaining studs and tighten to 13-16 ft. lbs. (18-22 Nm) in the sequence illustrated.
Raise and safely support the vehicle.
Position the Y-pipe assembly using a new flange gasket and install all the retaining nuts and bolts loosely.
Starting at the front of the system tighten the Y-pipe to exhaust manifold nuts to 26-34 ft. lbs. (34-46 Nm).

- Tighten the converter to transaxle nut and bolt to 30 ft. lbs. (40.3 Nm). Tighten the converter outlet bolts to 26-34 ft. lbs. (34-46 Nm).

zjlimited_1988.jpg

Fig. Right side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click image for zoom)


zjlimited_1989.jpg

Fig. Left side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click over image for zoom)

Hope this helps (remember to rating this answer).

Oct 06, 2011 | 1999 Ford Taurus

1 Answer

I need to know the torque specs for the head gasket for a 99 2.2 pontiac sunfire


Install cylinder head bolts finger-tight. New cylinder head bolts are recommended due to stretch of the old bolts.
Tighten bolts in sequence, tighten the long bolts to 46 ft. lbs. (63 Nm) plue 90 degrees. Tighten the short bolts to 43 ft. lbs. (58 Nm)


Install pushrode and rocker arms and rocker arm nuts. Tighten nuts to 22 ft. lbs. (30 Nm).


Install valve cover and tighten bolts to 89 inch lbs. (10 Nm).

Apr 05, 2011 | 1999 Pontiac Sunfire

1 Answer

What are the torque specs on the head bolts and rod caps on a 1999 nissan altima with a 2.4l engine


Rod cap nut's

Step 1 -10-12 Ft.LBS
Step 2 - 60-65 Additional Degrees


Head Bolt's

Step 1 - 22 Ft.LBS
Step 2 - 59 Ft.LBS
Step 3 - Loosen all bolt's
Step 4 - 22 Ft.LBS
Step 5 - 86-91 Additional Degrees

bcas1298_8.gif

Dec 11, 2010 | 1999 Nissan Altima

1 Answer

Change the water pump. what size is the bolts


Location, size and torque specification for the water pump bolts-3.0L OHV engine...

f2d2658.jpg

  • Install the bolts in the water pump housing.
  • Tighten bolts Nos. 4, 5, 6, 7, 8, 9 and 10to 15-22 ft. lbs. (20-30 Nm). Tighten bolts Nos. 11, 12, 13, 14 and 15 to 71-106 inch lbs. (8-12 Nm).
    The bolts are of different lengths and must be installed in the correct locations.
  • If equipped, attach the engine control sensor wiring to the locating stud bolt.
  • Hand-tighten the water pump pulley retaining bolts.
  • Install the accessory drive belts.
  • Tighten the water pump pulley bolts to 15-22 ft. lbs. (20-30 Nm).
  • Connect the heater hose to the water pump.

Hope this help (remember rated and comment this post).

Apr 10, 2010 | 1999 Ford Taurus

2 Answers

What is the tension on cylinder head bolts for a jeep grand cherokee 307935 4 litre, 6 cylinder, 1999, petrol motor.


Coat threads of left hand front bolt with sealant: 1st - step; - 22 ft./lbs. 2nd - step; - 45 ft./lbs. 3rd - step, all bolts except L.H. front bolt; - 110 ft./lbs. 4th - step, L.H. front bolt; - 100 ft./lbs. fig100.png

Sep 05, 2009 | 1999 Jeep Grand Cherokee

4 Answers

Chevy 5.7 17 bolt heads tork specs


Cylinder Head Bolt (Preferred Method) All Bolts First Pass in Sequence 22 ft.lb Long Bolt Final Pass in Sequence 75 deg. Medium Bolt Final Pass in Sequence 65 deg Short Bolt Final Pass in Sequence 55 deg. Cylinder Head Bolt (Optional On-Vehicle Strategy) First Pass in Sequence 26 ft.lb Second Pass in Sequence 44 ft.lb Final Pass in Sequence 66 ft.lb

Oct 13, 2008 | 1999 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...