Question about Cars & Trucks
Remove the rear seat or seats out the other door
if you cant remove the door card
source a replacement door card
then cut into the original
Posted on Dec 07, 2016
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2001 tahoe door panel
THE COUTESY LAMP IS HOT DUE TO THE DOOR BEING OPEN WHILE THIS PROCEDURE IS DONE!!!! First: Remove the triangle panel at the top of the door (behind the mirror). This is held in with two metal clips about half way down the panel. Do not pry at the bottom as there are two tabs that slide in to keep the module in place. I pulled the top of the triangle out by hand then could see the clips and used a straight screw driver to carefully pry from under the triangle panel so as not to scar the visible part after re-assembly. Once these two clips are disengaged the triangle should pull straight up and be free. Second: Carefully pry out the door lock insert. There are no significant tabs to worry about here. Again a straight screw driver and care should not leave any scars. The lock insert has no mechanical connection but simply is used to slide the lock rod. Re-installing you will need to align the slot for the rod in the lock or unlock position depending on the rod position. Third: Carefully pry out the insert that is located at the door handle. Start at the rear of the insert as this is where the clips are located and once the rear is out pull open the door handle and pull the insert to the rear so as not to break off the two front tabs. You will find two small screws (mine were black). One near the front and one at the rear of the door handle module. Both are 7 mm and are the only ones that need to be remove in the process. (I understand some door panels have an other screw at the very bottom of the door as well; guess you'll have to check you door. Fourth: Pry up the control panel for the automatic windows and unplug the wires. Here again start from the rear and once the rear is free pull the module to the rear and it should come free. There are tabs at the front that you do not want to break off. To unplug the wires - First remove the clips (mine were blue) that hold the plug in place. There is also a push catch on the plug that must be depressed to release the plug from the control panel. Fifth: My door had no push in 'buttons' or clips to hold the door panel in place. It simply lifted up and became free with the exception of the numerous wires attached to things like the speakers, the remote mirrow and courtesy light. Unplug these wires by first taking off any retaining clips (usually blue) and then unplug the wires. The courtesy light pulls straight out (toward the front) and watch your fingers as this is one hot little bulb. The door panel can then be totally removed and set aside. You may find it easier to remove the courtesy light lens by prying out the rear first and then pulling it toward the back of the door so as not to break the two front clips. I found it easier to do this and then install the bulb in the lens and then install the lens back in place. Six: I'm sure I don't need to say it but here goes - ' reverse the procedure to re-assemble'. Remember to poke the courtesy light wire out the hole and re-connect the remote mirror and speaker wires before the door is put in place. The wires to the window and electronic lock module can be installed after the door is back in place. Working by myself made the door difficult to handle during re-installation so I took a 'light' bungy cord and placed some protection over the top of the door and hooked the bungy into the opening were the door handle was to come through. This allowed me to steady the door and do the electrical connections as required. PS - we were replacing the power window motor and were able to 'force' the cable into the gears of the new motor by turning the motor and this saved a lot of further disassembly. The contacts on the new motor were reversed so I removed the pins from the plug going into the motor and reversed them - presto.
Posted on Mar 17, 2009
SOURCE: Diagram for removing door panel
Check this documents, in spanish, but you can find graphics to help in there:
- WJ-2002-Cherokee-Service-Manual-PDF-23-Carroceria (Body - Page 23-36 Fig. 14 and next)
- WJ-2002-Cherokee-Service-Manual-PDF-08S-Elevalunas-Electricos (Electric Windows)
Posted on Jul 27, 2009
SOURCE: Door panel removal
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
Posted on Aug 14, 2009
On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you need to pull back the weather seal and then you can access the bolts securing the outer handle
Posted on Nov 05, 2009
Tips for a great answer:
Jan 05, 2016 | 2001 Ford Explorer
Sep 16, 2015 | 2012 Ford Escape
Mar 22, 2015 | 1999 GMC Suburban
Jul 29, 2012 | 2003 Chevrolet TrailBlazer
May 08, 2012 | Chevrolet Impala Cars & Trucks
Nov 11, 2011 | 2000 Lincoln LS
Aug 21, 2011 | 1998 Ford Escort
Apr 17, 2010 | Mazda B-Series Cars & Trucks
Aug 06, 2009 | 1996 Lincoln Town Car
17 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: