Question about 1991 Honda Accord

1 Answer

Why do i need to remove a/c control unit on 91 accord to replace blower assembly when its not in the way . manual on how to do instructs that i do it

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 186 Answers

Most after mrket manuals are genaric and have you do steps not ness.

Posted on Jul 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My fan blower motor only works on high,They say it maybe the resistor may be bad, where is it ? Thanks, Jim


Hi, the resistor is screwed to the side of the blower housing behind the glove box. See procedure below to replace the resistor. You don't have to complete all steps in the procedure. just work your way to the point that you can unscrew the resistor. Please let me know if you have questions, and thanks for using FixYa.

1990-93 Accord

See Figures 2, 3 and 4
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support)

jturcotte_1481.gif

Fig. Fig. 2: Remove the glove box and frame

  1. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.

  2. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly.
jturcotte_1482.gif

Fig. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully


jturcotte_1483.gifjturcotte_418.jpg

Apr 04, 2011 | 1993 Honda Accord

1 Answer

How to install a blower moter and fan


Well, here's the instructions from the service manual. The labor guide says this can be done in 1.6 hours...I don't see how, unless the instructions are wrong about having to remove the instrument panel. My thoughts are that if you are only doing the blower motor, the blower assembly will come out without pulling the dash. You probably only have to do a partial disassembly and remove the glove box and the glove box lower support.

*************************************************************************************

BLOWER ASSEMBLY

Removal and Installation

1. Disconnect battery ground cable. Remove Instrument panel. (See Instrument Panel Removal) Disconnect resistor connector. remove blower assembly duct. Disconnect motor connector. Remove blower assembly

2. Remove blower assembly screws and blower motor assembly. Remove clip and fan from assembly. Separate motor case and remove blower motor. To install, reverse removal procedure.



INSTRUMENT PANEL

Removal

1. Disable air bag system. See AIRBAG RESTRAINT SYSTEM article in ACCESSORIES/SAFETY EQUIPMENT SECTION. Disconnect negative battery cable. Scribe mating marks on steering wheel and shaft for installation reference. Using Steering Wheel Remover (J-29752) remove steering wheel. Remove steering cowl.

2. Remove instrument panel grilles and plug, or driving pattern indicator panel (A/T Models). Disconnect electrical connections. Remove instrument panel hood, instrument cluster ezel and instrument cluster. Remove hood release handle. Remove knee protector.

3. Remove dash fuse/relay block and side trim. Remove engine control module box. Remove radio console and glove box lower reinforcement. Remove speaker covers and glove box. Remove heater control panel knobs and cover. Disconnect heater control cables, and remove heater control panel. Remove illumination control knob. Remove instrument panel.

Installation

1. Install instrument panel. Install and adjust heater control cables. To complete installation, reverse removal procedure. Ensure mating marks on steering wheel and shaft align. Apply grease to contact ring and tighten steering wheel nut to 26 ft.lbs. (35 N.m).

Feb 28, 2011 | 1995 Isuzu Rodeo

2 Answers

I cant find the blower motor


If you mean the climate control blower motor, it's usually under the dash on the passenger side on Hondas.

1990-93 Accord
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support) Fig. 2: Remove the glove box and frame 86806004.gif

  4. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
  5. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully 86806005.gif
      Fig. 4: Remove the lower covers from the blower unit 86806006.gif
      To install:
  6. Install the blower unit and tighten the retaining nuts.
  7. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.
  8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  10. If applicable, enable the SRS.
  11. Connect the negative battery cable.
1988-91 Prelude
  1. Disconnect the negative battery cable.
  2. Remove the glove box and frame (lower support).
  3. Remove the 4 screws and remove the heater duct. Fig. 5: The glove box and frame are secured by several small screws 86806007.gif

  4. Remove the 3 mounting bolts.
  5. Unplug the wiring connectors from the blower motor, resistor and recirculation controller. Remove the blower motor assembly.
  6. Reinstall in reverse order. Make certain the blower mating surfaces are tightly sealed.

Jan 08, 2011 | 1992 Honda Accord

1 Answer

Need to replace a front heat blower resistor on 2002 mdx, where is located???


moz-screenshot.pngHere's an excerpt from the 2002 Acura MDX 4WD 6cyl Repair guide for replacing what the reference manual calls the "control assembly" - its located under the console rear trim and may (or may not)
contain the blower resistor - my manual doesn't say - but this is the closest thing I could find for you. Every other blower resistor I've had to find was located close to the heater controls - and this
car seems to be no exception -- its heater controls are located in the console between the seats, rather than in the dash (as in Acura 2003-06 MDX models).

You may want to call your friendly Acura dealership ad speak to the parts department, to make sure where the blower resistor is located - or a visit to a dealership parts counter often (or
Advance Auto Parts is helpful too) ofen clarifies questions I have from Haynes manuals (the cheapest car repair guides).

All this assumes that you've correctly diagnosed your blower control problem -- as in "replace the blower resistor when the blower works only on the MAX/Highest setting."

-- begin excerpt from 2001-2 Acura 4wd 6cyl MDX Repair manual --
Control Assembly Removal & Installation

2001-02 Models
  1. Remove the console rear trim. Refer to the accompanying illustration.

    0996b43f80205cf3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Exploded view of the console rear trim

  2. Remove the self-tapping screws and the rear heater-A/C control unit (A) from the console rear trim (B).

To install:
  1. Install the control unit in the reverse order of removal. After installation, operate the control unit controls to see whether it works properly.
  2. Run the self-diagnosis function to confirm that there are no problems in the system.

    0996b43f80205cf2.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Remove the self-tapping screws and the rear heater-A/C control unit (A) from the console rear trim (B)



  3. --- end excerpt from 2001-2 Acura 4WD MDX 6cyl Repair Manual ---

Jan 02, 2011 | 2002 Acura MDX

2 Answers

Where is the blower motor located on a 91 Dodge Dakota and how do I access it?


Blower Motor REMOVAL & INSTALLATION Dakota
  1. Disconnect the negative battery cable.
  2. Remove the steering column cover, intermittent wiper control and the lower instrument panel module retaining screw to the right of the steering column.
  3. Remove the center distribution duct retaining screws and panel support screw at the bottom of the module. Fig. 1: Heating/air conditioning unit components - Dakota models 88476g01.gif

  4. Remove the courtesy lamp at the lower right corner of the module and the screw near the ash receiver.
  5. Open the glovebox and remove the screws along the top edge.
  6. Move the module out and down far enough to unclip the wiring harness and antenna cable and disconnect the speaker wire (if equipped with monaural radio) and glovebox light wire. Remove the module from the vehicle.
  7. If the vehicle is equipped with air conditioning, disconnect the two vacuum lines from the recirculating air door actuator and disconnect the blower lead wires.
  8. Remove two screws at the top of the blower housing, five screws from around the housing and remove the blower housing from the unit.
  9. Remove three screw attaching the blower to the unit and remove the blower from the vehicle.
  10. Remove the fan from the blower motor.
  11. Installation is the reverse of removal. Secure all components accordingly and check the blower motor for proper operation.
Pick-Up and Ramcharger
  1. Disconnect the negative battery cable.
  2. Disconnect the blower wiring. Fig. 2: Exploded view of the heater assembly components for Pick-up and Ramcharger models 88476g00.gif

  3. Remove the blower motor cooling tube. Fig. 3: Disconnect the wiring and cooling tube to access the blower motor - 1994-96 models shown 88476g06.gif

  4. Remove the screws or retaining nuts retaining the blower plate to the housing. Fig. 4: Unplug the wiring harness connector to the blower motor 88476p14.jpg
    Fig. 5: Unfasten the blower plate housing screws 88476p15.jpg

  5. Remove the assembly from the housing. Fig. 6: Lift away the blower plate housing for access to the blower motor 88476p16.jpg

  6. Remove the spring clip fastening the blower wheel to the blower shaft and pull off the wheel. Remove the blower from the plate. Fig. 7: Unclip and remove the blower wheel 88476p17.jpg

  7. Installation is the reverse of removal.
prev.gif next.gif

Oct 14, 2010 | 1991 Dodge Dakota

1 Answer

NEED INFO ON HOW TO FIND AND REMOVE BLOWER MOTOR IN A 1993 HONDA ACCORD. IT WILL NOT WORK ON ANY SPEED AND NEEDS TO BE REPLACED.


990-93 Accord
See Figures 2, 3 and 4
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support)
  4. If not equipped with air conditioning:
  5. If equipped with air conditioning:To install:
  6. Install the blower unit and tighten the retaining nuts.
  7. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.

  8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  10. If applicable, enable the SRS.
  11. Connect the negative battery cable.

8d1d518.jpg
efc7885.jpg

Dec 28, 2009 | 1993 Honda Accord

2 Answers

How do you replace the blower motor on 92 accord wagon - where is it located?


Disconnect the negative battery cable (if you have an anti-theft radio, make sure you have the code).
The blower unit is located in the dash, behind the glove box.
Remove the glove box and the glove box frame(damping screws on the sides and two screws underneath).
If the car isn’t equipped with air conditioning, remove the heater duct between the heater core and the blower assembly housings. Then remove the three blower housing retaining nuts, pull the blower housing out far enough to unplug the electrical connectors (at the lower right edge, right above the kick panel) and remove the blower assembly housing.
If the car has air conditioning, remove the strap bolt, the blower under cover and the three blower housing retaining nuts, then remove the blower assembly as previously described.
If you are replacing the blower motor itself, or either of the blower fan wheels, remove the motor, remove the retaining clip(s) and remove the fan wheel(s).
Reverse procedure to install.
Hope this helps you.

Oct 19, 2009 | 1992 Honda Accord

3 Answers

THE BLOWER MOTOR IS MAKING NOISES AND SMELLS


your bearing failed and is causeing friction replace motor

Jun 05, 2009 | 2001 Honda Accord

1 Answer

How do i pull out a faulty heater blower motor from behind glovebox in 91 accord?


For Pictured Detailed Innstruction see Bottom of Page


BLOWER UNIT REMOVAL
  1. Remove the glove box.
2. Remove Glove box FRAME
3. Pull back the carpet and remove the kick panel. Remove the control unit bracket mounting nuts (4). Disconnect the connectors (5) and remove the control unit and bracket.

  1. Without A/C:
    • Remove the self-tapping screws (3) and remove the heater duct.
    • Remove the blower (3 nuts).
  • If the car has A/C, remove the blower unit according to the sequence shown
  • BLOWER MOTOR REPLACEMENT
    Refer to illustration for blower unit disassembly and reassembly, noting the following:
    • Before reassembly, make sure that the air door and linkage moves smoothly without binding.
    • When reattaching the recirculation control motor, make sure its positioning will not allow the air door to be pulled too far. Attach the recirculation control motor and all linkage, then apply battery voltage and watch the recirculation control door movement. If necessary, loosen the holding screw and move the recirculation control motor up or down
    • CONTROL ROD ADJUSTMENT
      Connect the recirculation control motor connector to the main wire harness and turn the FRE/REC switch to "REC". Hold the air door closed, then connect the control rod to the clip on the arm.
    • Email Me at the nickkname shown here >>rejakwilson @aol.com

Jan 18, 2009 | 1991 Honda Accord

1 Answer

Air and heater


  1. Disconnect the negative battery cable.
  2. Remove the glove box.
0900c1528005f9e2.jpgFig. 1: The blower motor assembly is secured to the right side of the dashboard
  1. Remove the duct between the blower and heater box.
  2. Unplug the wiring connector and the vacuum hose from the blower.
  3. Remove the three mounting bolts and remove the blower assembly.
  4. Install in reverse order, tightening the mounting bolts to 7 ft. lbs. (10 Nm). Make certain the blower mating surfaces are tightly sealed. Install the blower duct; make certain there is no leakage at its joints.
1990-93 Accord
See Figures 2, 3 and 4
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support)
0900c1528005f9e3.jpgFig. 2: Remove the glove box and frame
  1. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
  2. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly.
0900c1528005f9e4.jpgFig. 3: Air conditioned models require the removal of the control unit. Handle it carefully 0900c1528005f9e5.jpgFig. 4: Remove the lower covers from the blower unitTo install:
  1. Install the blower unit and tighten the retaining nuts.
  2. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.
  3. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  4. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  5. If applicable, enable the SRS.
  6. Connect the negative battery cable.

Oct 16, 2008 | 1990 Honda Accord

Not finding what you are looking for?
1991 Honda Accord Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...