Question about Mitsubishi Galant

1 Answer

I have a mitsubishi galant that stalled when i was driving it and it will not start we changed the cam shaft position senser and the ignition coils and cleaned the positive cable'

The ecu when it goes out when you are driving and the car stalls and will not start for nothing what can I do

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 583 Answers

Check engine light? Have you checked trouble codes?

Posted on Dec 07, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Coil no power mitsubishi galant 4y 2006 im change timen belt bot no power in evry coil and chang cam shaft sonsor


Did you forget a ground wire attachment? Recheck your engine grounds.
Each coil should get power on the black/white from the ignition switch, constant battery voltage. Does it? If not, check fuse 24, a 10 amp fuse in the Junction Block. Power travels from the ignition switch (in ON, RUN, or START) to this fuse, and then is spliced to each coil. Other than that, the PCM controls the current switching for the coils (for spark). The other wire from the coil (black?) goes to the pcm for earthing the primary current to the coils.

If the coils have power but no spark, it could be the crankshaft position sensor. I believe the crank sensor would be more important than the camshaft sensor for the pcm to figure spark timing.

Mar 23, 2015 | Mitsubishi Cars & Trucks

1 Answer

PONTAIC G6 2008 2.4 CAM POSITION SENSER PROBLEM HOW TO CORRECT


Buy the sensor from the car dealership. The sensors at auto stores are inferior and sometimes do not work properly.

Jul 07, 2014 | 2008 Pontiac G6 Sedan

1 Answer

I am working on a 2003 mitsubishi galant and the timing belt was destroyed along with the crankshaft position sensor, balancer belt and the crankshaft sensor plate, now i have replace them and algined all...


Check to see if your getting voltage to your coil wire plug coming from vehicle, if there voltage at the plug then its most likely that when the crank shaft censor was damaged it may have shorted out your cam shaft sensor because they both run off the same system..

Jul 18, 2011 | 2003 Mitsubishi Galant

1 Answer

I changed the ignition switch in my 2000 galant and now my car wont start can someone tell me what to do? the ignition cam out of an 02 galant both cars ran befor i made the change.


call you mitsubishi dealership and talk with the manger but it sound like it to me the key may have to be reprogram to that switch wish you the best of luck Michigan Man

Jan 03, 2010 | 2000 Mitsubishi Galant

1 Answer

Driving down highway no signs of touble, totally stopped


a bad cam sensor will definitely make an engine not fire. I would start with replacing that.if that doesnt help, then look into the oil pressure sensor or maybe the oil pump? I know some cars have a safety circuit that disables the ignition if the pressure gets too low.

Sep 08, 2009 | 2001 Mitsubishi Galant

1 Answer

2000 Silverado-4.3 ltre-cranks over-wont start-consistenly puts out P1351 code-crank senser,cam senser, ignition control module, spark plugs and distributor have been replaced. Wiring from PCM to crank...


Yes. First, in the fuse block under the hood check INJ A fuse and INJ B fuse. INJ A fuse is circuit 1039 which feeds the coil. If the fuse is OK, replace the coil electrical connector. I stock 2 of these at my dealership because they are needed quite often.
FYI P1351 is an ignition coil control circuit DTC.

Aug 30, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

I am having trouble finding the cam shaft positioning sensor on our 2001 2.4L Mitsubishi Galant


The CMP sensor is mounted on the left end{opposite end from the timing belt}of the cylinder head...

Jul 12, 2009 | 2001 Mitsubishi Galant

1 Answer

Volvo automatic 850 fuel injection. car stalls unpredictably


check your plugs plug wires ignition coils and ignition amplifiers and cam sensor.change fuel filter if it has not been changed in a while.if its partially clogged will cause stalling problems.

Mar 01, 2009 | 1996 Volvo 850

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...