Question about 2000 Hyundai Elantra

3 Answers

Knock sensor can knock sensor caused 3rd gear to stall, not shifting to 4th gear?

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yes!
Same problem with my car, won't shift especially when cold.  I was told that if the knock sensor is sending a false signal to the computer that the engine is pinging then it will not allow the transmission to shift until the pinging stops.  Other people have had this problem too, check out this link, especially the last entry:
http://us.lexusownersclub.com/forums/lofiversion/index.php/t4941.html  

Posted on Sep 24, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,129 Answers

No the knock sensor merely adjusts the timing to prevent and compensate for the knocking condition this sensor has nothing to do with transmision shift patterns. Usaully a speed sensor may have the undesired effect you have. Unfortunately this car must go to the dealer to check for a transmission code which is not detected as a generic OBD II code at your local Auto Zone,sorry man.

Posted on Jul 20, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Nope. The knock sensor detects knocks in the engine and retards detonation in the timing.

Car not shifting would be bad vacuum operated actuator on outside of tranny or bad syncros or other internal transmission parts

Posted on Jul 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix ram 1500 2005 transmission that sometimes gets stuck in 3rd gear. from start to finish truck will stay in 3rd gear.


When did you last replace trans filter and fluid? Dirt may be causing shift valve to stick.

Dec 28, 2014 | 2005 Dodge Ram 1500

1 Answer

I have a 1998 dodge Grand Caravan with codes P0700,P0734 & P0733. What does this mean?


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Jan 22, 2013 | 2003 Dodge Caravan

1 Answer

Codes p0700,p0733,p0734 dodge caravan 1997


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Apr 03, 2012 | 2003 Ford Focus

1 Answer

Auto won't down shift when o/d button is pushed


This button only makes the gearbox change from 3rd to 4th or 4th to 3rd, will not down shift in any other gear, make sure it is in 4th gear, usually above 60km, than press o/d off it should go into 3rd gear, if it does not than see a automatic specialist, it is usually a sensor, if you go to Toyota they will charge you a fair bit.

Jun 08, 2011 | 1996 Toyota RAV4

1 Answer

1996 gmc jimmy will not shift to 3rd gear


Hi, It may be in LIMP mode.

What is "limp-home mode" ? This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Common failures on 4L60E, symptom any possible repair:

Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under-hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter :ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Trans seems noisy when moving in 1st and Reverse, noise goes away instantly if you shift to N or the trans goes into 3rd gear: Reaction planetary is worn out due to high miles or insufficient lubrication. Not a critical failure, but not a good sign either. R&R sooner rather than later.

3rd gear starts, can manually shift through all gears. When car has been turned off for a bit, then back on it will run normally.: VSS dropoff w/ Hi-stall converter. The rpms are too high, but VSS is showing no movement. Happens after a tire burning take-off. Doesn't store a code, will not throw a CEL (I've heard that it will store a code if it happens 3 or more times). Cure: Reprogram PCM for VSS dropoff -- PCMforLess knows about it.

If you can get the Jimmy for no more then $500.00 and the engine sounds good and body is good, you may want to invest in the repair of the jimmy. Also note that to have a close look at the fuel line along the frame on the drivers side just by the back doors, the line is know to corroded there on all the SUV's

Sep 19, 2010 | 1996 GMC Jimmy

1 Answer

4L 60E - 2001 k1500 will not shift into 3-4. Oil is not burn't and stifts great into1-2


  • No 3rd or 4th gear: “3-4” clutches are worn out. R&R. The car is safe to drive (in 2) until you can get it fixed.
  • Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.
  • No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : Shift A solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.
Check to see if your transmission is in the limp mode, which would only give you 2nd, 3rd and reverse gears. No 1st or 4th gear.

Nov 19, 2009 | 2003 GMC Sierra 1500

1 Answer

2004 mazda 3 transmission problem


Check transmission fluid. If that is full, try changing the fuel filter. It could be starving for gas, and trying to shift but can't. It could also be the speed sensor, or shift solenoid.

Jul 06, 2009 | 2005 Mazda 3

1 Answer

Hang up in third gear loss of power


Hi All

I have a s40 1.9d / 2000 plate,
In the last month or so the car loses revs when changing up to 3rd and 4th gear, I can only get 50 mph max in 3rd gear 80mp in 4th.
The car has just clocked 185,000 miles
Its a great car but a pai at the moment, I've had a service including fuel fillter change added fuel cleaners to the deilsel all to no avail


Any suggestions

Jul 06, 2009 | 2000 Volvo S40

3 Answers

E40d trans will not shift into 3rd or 4th gear, only rev. 1+2


check or replace your thottle position sensor tps that trans needs to know where the throttle is to shift if it is bad it will do as you say wont shift to third
another telltale is it will act like it goes into lockup when shifting into reverse and stall the engine

Jan 23, 2009 | 1995 Ford Club Chateau

Not finding what you are looking for?
2000 Hyundai Elantra Logo

649 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...