Question about 2005 Ford Escape

1 Answer

Code u2023 on 2005 ford escape

ABS light on 4WD light flashes intermitantly replaced CVaxle and speed sensors on left an left front wheels

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,593 Answers

U2023 External Node Fault DTC ABS Module REFER to Section 418-00 . U2023 Fault Received From External Node SJB REFER to Section 418-00 .
Do you know what U codes are about ? Which module did you find this code in ? Does scan tool communicate with all the module's on the vehicle .

Posted on Dec 06, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intermittent abs light


What make , model an year vehicle ? Is the wheel speed sensor integral to wheel bearing hub or separate ? Could be a corroded tone ring on half shaft . ABS activates on every stop damaged tone ring

Sep 13, 2016 | Cars & Trucks

3 Answers

What is the code C1247 pontiac grand am 2001?


left front wheel sensor is not reading replace wheel speed sensor

Jul 13, 2014 | 2001 Pontiac Grand Am SE

1 Answer

Where is the front vss abs in a 2006 nissan titan 4wd


perhaps you have a shorting wire. check carefully, my ABS always used to come on for no reason during driving and it turned out there was 2 terminals bent together and touching.

Nov 20, 2013 | Nissan Cars & Trucks

1 Answer

Abs on vr commodore light stays on solutions


Error logs are a great thing. They will help you find intermittent problems and start you off in a general direction of where a problem could be. There is a great level of detail on the justcommodores site on checking error codes logged by the engine management system, but this does not detail anything about the abs system. The abs warning light is not as common as the check engine warning light. Reading through the posts, I haven't found any detail on checking error codes logged by the abs system.

So here it is. For those of you familiar with checking the engine error codes, this procedure is so simple its not funny.

Basically, to check the engine error log, you bridge the 5th (ground) and 6th pins in the ODB connector under the steering wheel.

To check the ABS error log, using the same trusty calibrated paper clip, you simply bridge pins 5 and 12 of the connector.

To find pins 5 and 12, start at the top left hand corner. That is pin one. Going to the right, you count pin 2,3,4 etc. Once you get to the end, jump back to the start of the bottom left level of pins and keep counting. Pin 5 is about halfway along the top row, pin 12 is a little left of the middle in the bottom row.

Reading the error codes is the same procedure (counting the flashes), except now, the ABS light flashes (as opposed to the engine light when checking the engine codes).

The ABS log also uses code 12 firstly, with any errors logged shown after that. If no errors are logged, the 12 will flash again.

Error codes for the ABS error log (VR/VS) are as follows:

12 Diagnostic system operational
21 Right hand front wheel speed sensor fault
23 Right hand front wheel speed sensor continuity fault
25 Left hand front wheel speed sensor fault
27 Left hand front wheel speed sensor continuity fault
28 Wheel speed sensor frequency error
31 Right hand rear wheel speed sensor fault
33 Right hand rear wheel speed sensor continuity fault
35 Left hand rear wheel speed sensor fault
37 Left hand rear wheel speed sensor continuity fault
41 Right hand front inlet solenoid valve circuit fault
42 Right hand front outlet solenoid valve circuit fault
45 Left hand front inlet solenoid valve circuit fault
46 Left hand front outlet solenoid valve circuit fault
55 Rear inlet solenoid valve circuit fault
56 Rear outlet solenoid valve circuit fault
61 Pump motor relay circuit fault
63 Valve relay circuit fault
71 ABS control module internal fault

The above guide has been verified on a VR/VS. Checking the error log on all models prior to VR/VS is the same for the engine log, and I would assume that the same can be said for the ABS log, would be happy if someone could verify this for me.

Sep 21, 2013 | 2005 Mazda Tribute

2 Answers

06 Mercury Mariner...ABS light comes on after awhile driving and then the 4WD light blinks only when the ABS light is on. I just had an oil change and tire rotation done a couple of days ago. This is the...


HAVE VECHICLE CODE SCAN.SOUND LIKE YOU COULD HAVE BAD WHEEL SENSOR OR DISCONNECTED OR LOOSE WIRE.BECAUSE 4WD DRIVE NEEDS SIGNALS FROM WHEEL SPEED SENSORS AND VECHICLE SPEED SENSOR BEFORE AUTOMATIC TRANSMISSION AND TRANSFER CASE CAN SHIFT CORRECTLY.

May 08, 2011 | 2006 Mercury Mariner

2 Answers

2006 Ford Escape XLT. Anytime the vehicle gets in any mud, snow, or ice, it immediately starts flashing the 4WD indicator light.


Sounds like you may have a broken abs tone ring on the front axle shafts they have a problem with that start there

Mar 30, 2011 | 2006 Ford Escape

1 Answer

2000 bravada, abs light on, all fuses are fine, any ideas, and can this be linked to accuator, as 4 wheel drive will not disingage


ABS light is on due to a bad or dirty ABS sensor on the front wheel hub. Inspect the front wheel ABS sensor and wire leads on the front wheel inner hub where the speed ring is. The 4wd will not disengaged is common when the vacuum switch on top of the transfer case drives side has gone bad and needs to be replaced, you can pick one up at Auto Zone or Napa for around $25.00 and take about 20 min to replace with a wrench. At worst it's going to be a bad electronic Actuator at the transfer case or one of the speed sensor at the transfer case, but most likely it's going to be the vacuum switch if you don't have any Check engine light on. Good luck and keep me posted.

Jan 21, 2010 | 2000 Oldsmobile Bravada

1 Answer

2005 mazda tribute....abs problem


a speed sensor on the front,have the ABS system scaned for the codes(this will show you wich sensor is bad)

Sep 08, 2009 | 2005 Mazda Tribute

Not finding what you are looking for?
2005 Ford Escape Logo

Related Topics:

965 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...