Question about 2009 Jeep Compass

1 Answer

I don't have any idea how to change a signal module 2009 jeep compass

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

no such thing that simply (pops out in hand)
check fuses first. F8 and F17 F33
then scan it next? you must scan newer cars. or its all just water under the bridge. (wasted effort and cash)
no symptoms posted., btw.
zero. just easter egg hunt,
you do know some jeeps there is no such module , right>?
i have the 08 book here,
lets see what's there.

this car has no such thing, the
here is the path, (block diagrams, in words)
Lets say you turn left. (or right or hazards)
the steering module sees that.
then IT, send to the network command to all what want to listen
you are turning.
then the Cluster brain sees that and flashes,(all by itself)
this same network command goes to the TIPM up front (under hood)
this is a complex set of electronics here.
and has 100% full electronic drivers inside that drive all blinker lamps. it receives, those commands and then flashes 1 of 4 drivers to do that.(transistor drivers) with electronic overloads.

does not work any thing like a 1993, old jeep,
so back to square one, no symtoms.

check fuses
scan it, you must scan it,
if say the cluster does not flash there will be errors reported
telling you what happened. even communications errors on the network called CAN-BUS

Posted on Dec 07, 2016

  • deraljenk
    deraljenk Dec 08, 2016

    thanks all good



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I replace the Drivers side turn signal lens on a 2009 jeep compass

from inside the hood of cur=urse you might have to movea few things

Jan 26, 2015 | 2009 Jeep Compass

1 Answer

How do I change the led light in the cup holder of a 2009 jeep compass

the FSM book covers all this.
console off.
exact way, can vary by country, and by exact model of compass.
some cars have upgraded interiors. and come apart different.
but the book covers all that. just read it.

the factory service manual, read it.

Dec 13, 2014 | 2009 Jeep Compass

2 Answers

My 2009 Compass won't start/crank; no communication with PCM but scanner will communicate with TCM and ABS module

Double check the fuses (Inside the car and on engine bay), there is a fuse for the OBDII linkageand sometimes it works together with other systems (Power Outlets, Stereo, Switch, etc). A bad PCM would also cause that but is not very likely.

Mar 26, 2013 | 2009 Jeep Compass

1 Answer

2009 jeep compass

seven days left on the auction for the whole manual set.

Oct 14, 2012 | Jeep Compass Cars & Trucks

1 Answer

Where do i install block heater on 2009 jeep compass 2.4 litre

They pretty well all install in frost plug hole. Usually about half way down engine block. Messy, would not recommend doing it yourself,

Nov 23, 2010 | 2009 Jeep Compass

1 Answer

I have a 2007 Jeep Compass Limited 4x4 and the ABS, 4WD, ESP BAS and Anti-Slip lights are all on at the same time. They came on while driving and have went off then back on a few times and now they just...

The lights are being turned on by your BCM or Body Control Module. It's located under the driver's side knee bolster, but it will probably have to be taken to the Dealership to hook up their DRB III to ascertain as to why the BCM is turning on all of your lights.

"00 Buck"

Nov 06, 2009 | 2009 Jeep Compass

1 Answer

What is the fuse location for a 2007 jeep compass, turn signal

there is no turn signal fuse it is integrated with the fuse module.

Oct 27, 2009 | 2007 Jeep Compass Limited

1 Answer

How to disable TPMS in 2009 Jeep Compass? I want to put a winter tires on after market cheap rims.

I need to replace all 4 tpms on my 07 jeep compass.
I am trying to keep the cost down. If I buy after market sensors
do I need to go back to jeep to program them? help

Oct 07, 2009 | 2009 Jeep Compass

1 Answer

Daylight running lights

Please do not ask about something which can cause accidents.
It`s not a safe idea to disable your DLR`s.
They are there for your safety and the safety of other road users.
Sorry about being abrupt.
Good Luck, Have fun

Jan 31, 2009 | 2009 Jeep Compass

Not finding what you are looking for?
2009 Jeep Compass Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides