Question about Cars & Trucks

Open Question

I have inverter EPs/Charger model 1524,my problem is Th? wiring from Th? board with Th? relays.please can you send me Th? diagram that shows Th? wiring

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2014 dodge ram 1500 eps failure how do I fix or better yet how do I get my power steering to work its a electric and I don't under stand is there fluid if so where does it go


I have no wiring diagram on 2014 eps, so I looked at 2013, hope they are the same?
https://s26.postimg.org/lgarr71eh/eps.jpg
Click on the link.
Check those two fuses, not only check the fuse, use a test light and check voltage on fuse circuits. The component at lower left is eps module. As you can see black wire is ground, check that also.
Check for applicable trouble codes? My info for 2013 no electrical component, eps, can be serviced separately. I definitely do some testing. If you have to replace eps motor and module, I don't the cost of the fix? I don't know if 013 and 14 are the same? Just trying to help.

Aug 28, 2017 | Dodge Cars & Trucks

3 Answers

Engine fan stays running all day . it just started ,


What make , model and year vehicle ? You mean cooling fan's for the radiator . Some makers use a module to control the cooling fans others use relays . Looking at a wiring diagrams would show control componets . Relay contacts could be stuck sending constant B+ voltage , keeping fans on , same with a control module .

Jan 24, 2017 | Cars & Trucks

1 Answer

How do you check the fuel pump at the relay on a olds achieva 3.100 6cyl.


What is model year? Does the relay have diagram on it? The load side of relay usually shows as open switch, that should be load side of relay, use jumper wire between those two terminals on the load side, with relay unplugged. That should send voltage to pump. One of those terminals should be hot all the time. This is just for testing not driving. Even if fuel pump runs, that doesn't mean it will start?

Did you use a gage and check proper fuel pressure?

Dec 07, 2015 | Cars & Trucks

1 Answer

Why is my Remote showing relay fault


315Mhz remote relay switch kits - 2 channels - Seeed Studio

www.seeedstudio.com/.../315Mhz-remote-relay-switch-kits-2-channels-p...
This remote switch allows you to remotely control any 12 Volt DC device. ... to supply 3-5VDC to the "+12V" pin,(Caution: the 12v is an error silk screen on PCB, ... Is there a wiring diagram to show how you connect the sender to the GPIO pins?

Amazon.com: 1 Channel Wireless Controller (On/Off) 12V ...

www.amazon.com > ... > Lighting Accessories

Amazon.com, Inc.I wired this remote relay to a fuse block below the motorhome frame. ... Here's a (very) short video showing how the remote control works. I love it! It's very easy to ...

12v wireless 315 MHz remote control relay board 6-channel ...

? 4:36
https://www.youtube.com/watch?v=JBzL0MIno2w
Feb 2, 2013 - Uploaded by Julian Ilett
12v wireless 315 MHz remote control relay board 6-channel ... The relay board takes 12 volts in and there ...

Dec 03, 2015 | Cars & Trucks

1 Answer

The top cover to relays on a f150truck is gone i need to know what relsy goes to what looking for the windshield wiper relay.please


What year F150 ? Go to www.bbbind.com free wiring diagrams , tsb's , fuse / relay box picture (diagram) . Click on technical information . Next page click on

bulletin.gif
Technical Service Bulletins & Wiring Diagrams

All TSB's and diagrams for every make and model - FREE
next page go to bottom an click I agree . next page click wiring diagrams. Then add your vehicle info , year ,make , model ,engine , then under system click on electrical distribution . then subsystem click fuse panel .
next

Nov 01, 2015 | Cars & Trucks

1 Answer

If I jump the wires to th fuel pump it will pump gas. I have 12volts to th pump relay I have 12v to th throttle injectors but no pulse. I have 12v to th coil but no fire. Got 12v to all fuses. Th code...


Hi, try installing a relay to supply current to the pump, you might have to install a new off/on switch to activate pump with relay(safety measure). Hope this helps with problem.

Apr 18, 2014 | 1992 Chevrolet K1500

1 Answer

All fuses are good. Brake switch is releasing shifter and allowing me to get out of park so my assumption is brake switch is ok. I feel it is alarm related and wondering if there is a brake light relay?...


You need to test the brake light switch, it is above the brake pedal and it is actuated by the brake pedal arm. Press the brake, the switch connector should show 12 volts on both sides, if not the wiring connector is defective or the switch is defective. Below is a diagram of a typical brake switch which is #4 in diagram.
11_7_2012_10_06_06_pm.gif

Nov 07, 2012 | 2008 Dodge Charger

1 Answer

Th magna wiring diagram


We do not have diagrams for this model. USA only, Sorry.

Aug 06, 2012 | 1999 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...