Question about Cars & Trucks

Open Question

Predator 24 blade brake assembly - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the #24 fuse located at for the third brake light


Year/make/model didn't post. The high mount brake light is not fused seperately. It should be on the same fuse as the brake lights. If it is not working check for a bad bulb. If the assembly is LED, check for power and ground at connector to light. If power and ground ok, suspect defective LED assembly

Feb 12, 2016 | Cars & Trucks

1 Answer

How too release the emergency brake foot pedal when the cable is broken?


About 73,400 results (0.87 seconds) Search Results

    Parking brake release cable snaps - Chevy Avalanche Fan Club of ...

    chevyavalanchefanclub.com > ... > Problems: Brakes

    24 posts - ‎16 authors
    Went to release the parking brake on my 04 and the cable snapped. ... More like the end cap coming of the cable that attaches to the foot pedal. ..... Then I released the parking brake, pulled out the broken release cable/handle assembly, ...

    How To Install Repair Replace Parking Brake Release ...

    ? 5:54
    https://www.youtube.com/watch?v=qx0oGfV62NQ
    Jun 23, 2011 - Uploaded by 1A Auto Parts
    How To Install Repair Replace Parking Brake Release CableHandle ... or replace a broken or worn out parking brake release cable handle.

    Emergency Brake Pedal Assembly & Stuck Brake Cable ...

    ? 10:13
    https://www.youtube.com/watch?v=0jYfvthBzhU
    Apr 17, 2014 - Uploaded by corgLLC
    Emergency (Parking) Brake Pedal Assembly & Stuck Emergency (Parking) Rear Brake Cable The emergency ...

    E-Brake Cable Broken? Stuck Emergency Brake... Help Please ' Chevy ...

    www.tahoeyukonforum.com > ... > Engine & Drivetrain


Jan 25, 2016 | Cars & Trucks

1 Answer

Instructions and diagram,to remove and replace rear drum brakes


1984 Ford Tempo - Rear Drum brake drum/shoes
REMOVAL & INSTALLATION


See Figures below instructions

1. Raise and safely support the vehicle with jackstands.

2. Remove the wheel, tire, hub and finally, the drum assembly.

3. Using a spring removal tool, remove the horizontal securing spring at the top first of the assembly.

4. Pull the adjuster locking plate away from the shoes.

5. Remove the lower horizontal securing spring.

6. Unfasten one of the 2 shoe hold-down springs and remove the pin.

7. Remove the brake adjuster.

8. Remove the remaining hold down spring and clip.

9. Lift the brake shoes assembly off the backing plate and wheel cylinder assembly. Be careful not to bend adjusting lever during the removal process.

10. Remove the parking brake cable from the parking brake lever.

11. Remove the horseshoe retaining clip and spring washer and slide the lever off the parking brake lever pin on the trailing shoe.



To install:

12. Apply a light coating of high temperature grease at the points where the brake shoes contact the backing plate.

13. Apply a light coating of lubricant to the adjuster screw threads and the socket end of the adjusting screw. Turn the adjusting screw into the adjusting pivot nut to the limit of the threads and then back-off 1 / 2 turn.

14. Assemble the parking brake lever to the trailing shoe by installing the spring washer and a new horseshoe retaining clip. Crimp the clip until it retains the lever to the shoe securely.

15. Attach the parking brake cable to the parking brake lever.

16. Attach the lower retracting spring to the leading and trailing shoe assemblies and install to backing plate. It will be necessary to stretch the retracting spring as the shoes are installed downward over the anchor plate to inside of shoe retaining plate.

17. Install the adjuster screw assembly between the leading shoe slot and the slot in the trailing shoe and parking brake lever. The adjuster socket end slot must fit into the trailing shoe and parking brake lever.



The adjuster socket blade is marked R or L for the right or left brake assemblies. The R or L adjuster blade must be installed with the letter R or L in the upright position, facing the wheel cylinder, on the correct side to ensure that the deeper of the 2 slots in the adjuster sockets fits into the parking brake lever.

18. Assemble the adjuster lever in the groove located in the parking brake lever pin and into the slot of the adjuster socket that fits into the trailing shoe web.

19. Attach the upper retracting spring to the leading shoe slot. Using a suitable spring tool, stretch the other end of the spring into the notch on the adjuster lever. If the adjuster lever does not contact the star wheel after installing the spring, it is possible that the adjuster socket is installed incorrectly.

20. Inspect your work to make sure it is correct.

21. Install the hub/drum and wheel/tire assemblies and adjust the wheel bearings.

22. Lower the vehicle and check brake operation.


archaeology_43.jpg

Fig.1 Exploded View of Rear Brakes - 1984 Ford Tempo

archaeology_44.jpg

Fig 2. Remove the brake shoe upper retaining spring with a suitable removal tool.


archaeology_45.jpg
Fig.3 Removed retaining spring - note spring direction.

archaeology_46.jpg

Fig.4 Remove the adjuster lock plate. Note the direction of the tab.

archaeology_47.jpg

Fig.5 Remove the lower retaining spring.

archaeology_48.jpg

Fig.6 Remove the Hold Down Spring - note brake spring tool used.

archaeology_49.jpg

Fig.7 remove the shoe adjuster. Note direction of the adjuster spline.

archaeology_50.jpg

Fig.8 Remove the hand brake cable.

archaeology_51.jpg

Fig.9 Remove the final brake shoe.

archaeology_52.jpg

Fig.10 All removed parts in order and properly oriented for re-assembly.

Apr 17, 2011 | 1984 Ford Tempo

1 Answer

REAR BRAKES SHOES INSTALLATION HOW TO INSTALL


This is a pretty straight forward repair. Normally the hardest part of the repair is dis-assembly of the rear brake assembly components and retaining clips. There is a special tool, set of pliers you can purchase to simplify some of this but typically you can do the job with a Pair or Regular pliers, pair of Needle nose pliers and a large blades flat screw driver. For step by step instructions and illustrations of the work area I recommend the Haynes Repair manual for your vehicle.

Sep 30, 2010 | 1999 Mercury Cougar

1 Answer

Replacing fan clutch


prev.gif next.gif Engine Fan REMOVAL & INSTALLATION Except 5.2L Engines VISCOUS DRIVE FAN
  1. Remove the upper fan shroud bolts and lift the shroud from its lower securing tabs. Fig. 1: Remove the fan shroud 86743p24.jpg

  2. Remove the accessory drive belts.
  3. Remove the fan flange-to-pulley mounting nuts. Fig. 2: Remove the fan flange-to-pulley mounting nuts . . . 86743p25.jpg
    Fig. 3: . . . then remove the fan assembly 86743p26.jpg

  4. Remove the fan and viscous drive as an assembly.
  5. Remove the fan blade-to-viscous drive bolts and separate the assembly. To install:
  6. Position the fan on the viscous drive. Install the bolts and tighten them to 187 inch lbs. (24 Nm).
  7. Position the mounting flange of the viscous drive assembly onto the pulley. Install the nuts and tighten them to 18 ft. lbs. (24 Nm).
  8. Install the accessory drive belts.
  9. Insert the shroud into its retaining tabs and install the upper bolts.

Aug 11, 2010 | 1996 Jeep Grand Cherokee

1 Answer

2005 Honda Odyssey brake light housing removal


Yes, there is a spear point style clip that is holding the assembly. Wrap a flat blade screwdriver with some masking tape (prevents paint scratches) and pry between the forward outboard corner of the brake light housing and the car body. You want to pry the assembly rearward.

May 31, 2009 | 2005 Honda Odyssey

1 Answer

2004 Honda Odyssey EX brake light replacement. How do you remove


open the rear hatch. Next to the brake light assembly, between it and the hatch there are two flap doors in the brake light trim. Take a small flat blade screwdriver and open these doors. The hinge side of the flap is nearest the hatch opening. When opened, the flaps will reveal two screws. Remove these. Then wrap a flat blade screwdriver with some tape (protects the paint) and put the blade at the front outside corner of the brake light assembly. Pry gently rearward and a plastic spear point clip will release. With the assembly off, you can see how to twist out the bulb sockets and replace the bulbs. to replace, put the spear point clip in first, replace the screws, and close the flaps in the trim.

May 30, 2009 | 2004 Honda Odyssey

1 Answer

Need to replace the left rad fan motor, any ideas on how to do it if i have the new part?


  1. Remove radiator from vehicle.
  2. Remove fan shroud retaining bolts, and cooling fan motor/blade/shroud assembly.
  3. Remove fan blade retaining clips and blades.
  4. Remove motor mounting screws and motors.
  5. If necessary, remove Constant Control Relay Module (CCRM).
  6. Reverse procedure to install. Torque CCRM screws to 40-56 in lb, and shroud retaining bolts to 24-48 ft lb.

May 27, 2009 | 1996 Lincoln Continental

1 Answer

Need to take off fan clutch, have taken off parts in the way


4.9L SFI
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding Tool T84T-6312-C Fan Clutch Nut Wrench T93T-6312-B
Removal
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The large clutch assembly nut has a right-hand thread and must be rotated counterclockwise to remove it.
    Remove the fan clutch (8A616) from the water pump (8501) by turning the large nut, which is part of the fan clutch, using Fan Clutch Holding Tool T84T-6312-C and Fan Clutch Nut Wrench T93T-6312-B.
  1. Remove two screws retaining fan shroud.
  1. Remove the fan blade (8600), fan clutch and shroud.
  1. If the fan blade and fan clutch have to be separated, remove the remaining bolts attaching the fan blade to the fan clutch
b098d2e.gif


5.0L, 5.8L and 7.5L Engines
Removal
  1. Remove screws retaining fan shroud (8146) to radiator (8005).
  1. Remove four screws retaining clutch on water pump hub.
  1. Pull fan clutch and fan blade off water pump pilot and remove fan clutch, fan blade and shroud from vehicle.
  1. Remove four screws and separate fan clutch from fan blade.
4d17f8c.gif

Item Part Number Description 1 8509 Water Pump Pulley 2 57632-S Screw and Washer Assembly, 5/16-18 x .62 Hex 3 8600 Fan Blade (5.0 and 5.8L) 4 8600 Fan Blade (7.5L) 5 8A616 Fan Clutch 6 380288-S2 Screw and Washer Assembly, 5/16-24 x .88 Hex A — 16-24 Nm (12-18 Lb-Ft)

Mar 10, 2009 | 1994 Ford F150 Styleside Supercab

1 Answer

2002 Honda Odyssey brake light replacement


open the rear hatch. Next to the brake light assembly, between it and the hatch there are two flap doors in the brake light trim. Take a small flat blade screwdriver and open these doors. The hinge side of the flap is nearest the hatch opening. when opened, the flaps will reveal two screws. Remove these. then wrap a flat blade screwdriver with some tape (protects the paint) and put the blade at the front outside corner of the brake light assembly. Pry gently rearward and a plastic spear point clip will release. With the assembly off, you can see how to twist out the bulb sockets and replace the bulbs. to replace, put the spear point clip in first, replace the screws, and close the flaps in the trim.

Mar 05, 2009 | 1997 Honda Odyssey

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...