Question about Cars & Trucks

1 Answer

What kind of wrench fits the head bolts on an idea

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 52,086 Answers

IDEA what , use your head you have a set of wrenches test the fit

Posted on Dec 06, 2016


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1055 Answers

SOURCE: allen wrench size to fit caliper mounting bolt

some are 7/16 and some are 3/8 amd some are torx

Posted on May 30, 2009

  • 101 Answers

SOURCE: The screw heads on the 2000 Nubira thermostat I do not recognize. Is there a special tool for removing them?

Check with atwelve head socket or rench check in the auto parts

Posted on Jul 30, 2012

SOURCE: What size allen heads are on the mounting bolts of the front brake caliper of 1989 Chevy Celebrity?

Then it has to be a Metric Allen Size

Need to get a complete set of Domestic,
Metric & Torx Drivers,then you have all you
need for any brake work, as well as other repairs,
for any vehicle

Snap-On Tools--- while expensive, is the way to go

Posted on Sep 20, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Bolt-head oil drain-plug stripped cannot remove

Get a stud bolt extractor looks just a socket most parts houses carry them and so does harbor freight tap it on bolt head and use ratchet to extract bolt

Nov 21, 2017 | Cars & Trucks

1 Answer

What size socket fits 2007 Pontiac torrent automatic transmission fill plug or bolt

That's it in the pic? Kind of hard to gauge the bolt size from the picture. It must be metric, though. My guess, it looks like a 17 mm socket or wrench would fit. 15, 17, 18, or 19 mm, those are probably the choices. Don't you or a friend have wrenches or sockets that you could try?

Nov 05, 2016 | 2007 Pontiac Torrent

1 Answer

The socket will not stay on keeps falling off

Don't know what type/size you need a "deep well socket"? this allows for a taller bolt head...also does an open end wrench/box wrench fit over the bolt? Are you lubricating with PB Blastor spray to loosen corroded bolts?

Sep 18, 2015 | Cars & Trucks

1 Answer

What size is the lower adjusting bolt on the alternator & can the fan belt be easily adjusted

no engine options stated,
cant fix engines or get help if you dont even know what is there..... the EPA sticker under hood tells you, or post the VIN. the VIN has engine codes.
3.2 L 6VD1 SOHC V6
3.2 L 6VD1 DOHC V6
3.5 L 6VE1 DOHC V6
3.0 L 4JX1 TD I4
3.1 L 4JG2 TD I4

did you try a 13 or 14mm wrench or socket yet?

Aug 08, 2015 | 2000 Isuzu Trooper

1 Answer

Free answer "93 Lexus head bolt torque

it means that after the initial torque setting of 25 ft/lbs you put the torque wrench away and use a socket and bar to move the head of the bolt the required number of degrees as per the angle gauge that you will fit over the head of the bolt
so select the first hard stud and torque to 25 ft/lbs
repeat this to all the other head studs in the pattern required to achieve even tightening of the head
put the torque wrench away and fit the angler meter (gauge) on the 1 st stud and tighten to 60 degrees as indicated on the gauge
repeat the process for all the head studs as per the tightening sequence
then start again and tightened again another 60 degrees and so on
modern engines use degrees to achieve the correct stretch of the bolts to get the prescribed crush on the gaskets
this is because engineers found that dry threads , dirty threads and dirty stud holes do not give repeatable tensions on all studs.

May 19, 2015 | Lexus Cars & Trucks

1 Answer

What the best way to remove seized head bolts

First try bashing the bolt head straight downwards. This may loosen the corrosion in the threads. Take care not to hit surrounding structures.

Next try a large impact wrench (you can hire them) with a high strength socket which is a good fit. Take care the wrench is set to run in the undo direction.

Apr 21, 2015 | 1988 Mercedes-Benz 300

1 Answer

I am trying to replace the speed sensor and cant get a wrench on the bolt . what size socket ,wrench fits or is there a special tool that i need

Hello: There should be a 10mm bolt head that holds a clip. This clip keeps the speed sensor in place. Use a 10 mm wrench, socket to remove bolt/screw.

Aug 06, 2011 | 2004 Chevrolet Impala

1 Answer

What tools do I need to replace the rotors on my 1995 Olds Cutlass Supreme

You will probably need some wrenches and allen wrenches to remove the brakes. A C clamp to compress the brake calipers when you go to put them back on. A pair of pliers to remove the retainer washer if there is one where the rotor fits over your wheel studs. Some vehicles require a Torx head socket to remove the bolts that hold the brake calipers or it might require a small socket if it's a regular bolt head. Probably not a bad idea to go to your local library and find a Chilton's manual for your year of vehicle. They give good instructions on how to change stuff.

Dec 04, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Trying to fit my own head gasket on pinto engine 2.0 do i need to use a gasket sealant and bought a torque wrench to refit cylinder head but dont know how to fit it

Use no sealer or treatment of any kind. To torque the head bolts you must go in a military rotation.Think of it as a spiral starting with one of the center bolts and working your way out to the ends. The torquing should be done in three stages, fist bring them down to 30 foot lbs. then going from the center again, this time in the opposing spiral, bring them down to 60 foot lbs. And lastly, bring them down to the specified tightness in your manual usually around 85-90 foot lbs. On the thrid sequence return to the original spiral direction that you started out with. Good luck, Dana

Sep 06, 2009 | 1989 Ford Probe

1 Answer

2001 Dodge Ram 1500 Water Pump?

can we have a picture of fan/pump assembly?
if not, just fit the correct size of wrench on the bolts.
if you have adjustable wrench that could reach those bolts.
use socket wrenches, or close type wrench.

email me the picture.

Nov 06, 2008 | 2001 Dodge Ram Maxi

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15148 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides