Question about Hyundai Getz
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: hyundai getz
if the speedo still works then it will need a spedo unit if the speedo doesn't work it is either the cable or the gear in the trans to check the cable unthread from trans and attach a drill to the cable innereds spin the drill if the speedo does not move replace the speedo cable
Posted on Oct 18, 2008
two points 1 replace batterys in fob .2 place key in drivers door and turn this acts as a reset might take a couple of turns.hope this helps you.adrian
Posted on Feb 18, 2009
SOURCE: Trouble With Seat Controls
Thank You ghost4548, we went back to the dealership and it was a small fuse problem. It was a tad awkward since we went back to the dealership to fix this problem 2 days after we went to the dealership to BUY this car!
Posted on Jun 02, 2009
SOURCE: Fuse problem in hyundai getz
dear friend -the fuses you describe is cluster fuses and has nothing stopping or starting of the engine.they are joint in a yellow holder.i think you might have a short be hind the fuse box,thats wh you keek on blowing that fuse.
Posted on Jul 21, 2009
I just solved the problem for a stuck rear center seat belt in my 2002 Jetta.
Flip the base seat cushion forward against the front seat backs. Trace down along the belt to its tether point on the floor. The belt is sewn around a steel loop. The loop is anchored to a black steel hook. A thin silvery retainer plate is spring tensioned on top of the loop to prevent it from sliding off of the hook when the seat back is folded.
Therefore, you need to press the silvery retainer plate away from the hook (push up) to allow the loop to be slid from the hook. The belt was tight with the seat back in the upright position, so it was necessary to fold the seat back forward to create slack in the belt. Now push the belt loop towards the trunk and slide it off of the end of the hook (only possible with the retainer plate pushed up out of the way).
Now with total release of tension on the system via the bottom end of the seat belt being untethered and with the seat back returned to the upright position, normal extension and retraction of the belt will be reestablished. Next, simply extend the seat belt and slide the loop back into place over the floor hook. It snaps past the silvery retainer plate without all the effort required to hold the plate up during removal of the loop during disassembly.
Check again, the seat belt should be extending and retracting properly. Now just put the seat cushion back into regular position and you will be able to safely buckle up three people across the back seat.
It took about as long to do this repair as it has taken to post this answer to the problem. Note, the seat belt safety mechanism only allows normal extension and retraction of the belt when the seat back is upright.
Posted on Dec 18, 2009
Tips for a great answer:
Nov 16, 2017 | Hyundai Cars & Trucks
Feb 26, 2016 | Hyundai Cars & Trucks
Nov 20, 2012 | 2008 Hyundai Getz 1.6
Oct 30, 2012 | 2005 Hyundai Getz 1.6
Mar 11, 2012 | 2010 Hyundai Getz 1.5
Jun 05, 2010 | 2009 Hyundai Genesis
Mar 10, 2010 | 2009 Hyundai Accent
Aug 15, 2009 | 2003 Hyundai Accent
Jul 02, 2009 | 2002 Hyundai Accent
Jun 01, 2009 | 2001 Hyundai Sonata
26 people viewed this question
Usually answered in minutes!