Question about 2000 Isuzu Trooper
RIGHT side, front or rear.??????
same as all car, watch youtube and 1000s doing same.
all cars have these ways, looking 1 time solves it,
no photos by you,
look at the lamp.
it has a lens.
Posted on Dec 07, 2016
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
easy under the driver side need fuel tool from auto store. 30 min or srew driver push the clips in and pull. carefull lots of gas...
Posted on Jan 09, 2009
If the fluid is up -
it could be a vacume loss or the shifting module..
The shifting module is what tells it to shift - and it is controled by vacume pressure..
Posted on Jul 08, 2009
First their are two different front axles in 1996 troopers. Isuzu changed the 4wd system from auto lock hubs to drive control axle.auto lock hube are on the older trooper's with the light and wiper switches on the dash. The same way to change both. Auto hub remove the six hex. screws slide off the hub remove the sirclip from the driveshaft. Newer hub has 6 alan-head screw's again remove them then the hubcap then the sirclip on the shaft and slide off the round spacer. Next 4 bolts from the lower balljoint and the brake's. Pull out the hub until it clear's the shaft remove the inner boot clips slide the inner boot out the shaft. Clean the grease from the end of the axle then with your fingernail feel along any of the 3 tracks in the axle and near the outer end of the track you will find a wirelike split ring slide a screwdriver under the ring and lever it off . Pull out the drive clean off the grease. You will see a sirclip on the end of the joint remove it and slide off the joint. You can replace either boot from that end. The outer joint is held on with a snap ring on the shaft inside the joint and is not easily removed need a hammer and drift to drive off the end and when removed its hard to get the snap ring on the shaft back into its place.You can change both boots from this end as well. Cheers
Posted on Sep 28, 2009
SOURCE: brake light bulb
I have a 2000 Isuzu Rodeo and had the same problem. On the 2000, there are 2 screws on the side of the light assembly and 1 at the bottom the need to be removed. I found I needed a longer philips screwdriver for the bottom screw as there is not much room. Once you remove the screws, pull straight back on the unit. There are 2 plastic pins that are about 3/4" that will pop out of their socket when you pull straight back. Then, just lift the unit out and replace the bulb.
Posted on Jan 03, 2010
Tips for a great answer:
Mar 24, 2017 | 1996 Isuzu Trooper
May 24, 2014 | 2000 Isuzu Trooper
Nov 05, 2012 | 2000 Isuzu Trooper
Jun 25, 2017 | 1991 Isuzu Trooper
Jun 12, 2010 | 2000 Isuzu Trooper
Oct 06, 2009 | 1993 Isuzu Trooper
Jun 20, 2009 | 2000 Isuzu Trooper
Feb 21, 2009 | 2000 Isuzu Amigo
Jan 10, 2009 | 2002 Isuzu Axiom
16 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: