Question about 2003 Ford Ranger

Open Question

Find thermostate housing in a 2003 ford ranger 2.3 motor

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Locate thermostate housing on a 2003 ford ranger 2.3 motor

its on top of the engine in the front follow the radiator hose to the top of the engine..the gooseneck is installed with a couple of bolts the thermostat is below it

Dec 06, 2016 | Ford Ranger Cars & Trucks

2 Answers

Which way does thermostat face?

the side without the spring towards the rubber hose/rad

Mar 14, 2013 | 2003 Ford Taurus

1 Answer

How do I get the Thremostat housing off my 1992 ford Ranger XLT 2.3

To change that thermostat you need to follow the top radiator hose to the motor from the radiator. It will lead to the thermostat housing on the block. The housing will be anchored with (2) bolts to the block (I think). Take the housing off and the thermostat is housed will have to replace it with a manufactured suggested thermo(probably 180* or 200 degree thermo).

Jan 29, 2011 | 1992 Ford Ranger

1 Answer

Where do I fond the resister for the heater fan motor. The fan works on high but no other setting

Sit next to the fan motor, on the same housing the fan bolt's to, resistor held on with two small screw's.

Jun 26, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

Quite lo cables de las bujias de una troca ford ranger 2003 3.0 motor, y ahora no recuerdo como ponerlos de vuelta en su lugar como estan enumerados

Para el modelo 2003 Ford Ranger 4WD 3.0 liter V-6 VIN "U" revise este diagrama...


Espero que esto sea de ayuda; recuerde valorar y calificar esta respuesta; gracias por usar Fixya.

Mar 31, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

How do I change the thermostate in a 95 ford ranger

follow the upper radiator back to the block it should hook up to the thermosts houseing drain the antifreeze below that level .remove houseing clean the gasket off. install the new thermostat and gasket

Jan 31, 2010 | Ford Ranger Cars & Trucks

1 Answer

Heater blower only works on the 2 highest speeds ? Ranger is 2003 4 dr. with factory air

it could be the blower motor resistor, this is what gives the motor different speeds, they are very common to burn out 1 or 2 speeds. They are not very expensive, I would look into that first

Nov 18, 2009 | 1999 Ford Ranger SuperCab

1 Answer

I replaced the water pump and all my hoses are

remove thermostat housing-check that 'o'ring was in it's groove-check that thermostat is in it's ''well'' & it's not in backwards--'pellet' towards motor,spring towards radiator.check that housing wasn't cracked when installing.clean mating's always the little things that get ya!

Sep 24, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

Heater restors

It is located in the blower housing itself, somewhere near the blower motor...should be 2-3 screws holding it in

Aug 29, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Dual cat back exhaust

I have found that the ranger is a lone wolf, there are not a lot of options for exhaust. your best bet would be to get one custom made. Not much more than one you buy from the parts house and buckle it together yourself.
tell the shop owner you wand magna low mufflers and I actually had the cats replaced..that all cost me about 700 bucks and it is Stainless welded.. well worth it and I had the size increased by1/2" it breathes so much easier and you know as well as I the 20 MPG is a pipe dream but that gave me 22..

Mar 04, 2009 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
2003 Ford Ranger Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5653 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides