Question about Nissan Cars & Trucks

Open Question

What is the part number for a water pump for a TCM FG20 forklift? It's a H20 Nissan motor. Probably early 80's year model.

Posted by on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 77499 Answers

SOURCE: Red light in tcm forklift dasbord

This is the car and truck section. Please post in correct category.

Posted on Jul 17, 2013

  • 468 Answers

SOURCE: When was my Colt 1861 Navy .36 Cal. produced (Serial #8986) Thank you Tim Smith

This link should be helpful.


Posted on Jan 12, 2015

Testimonial: "Bob...what a great help! Thanks You :) Looks like it was built in 1862 mid year. You are the greatest Tim"

  • 1103 Answers

SOURCE: Need an exploded diagram for the engine in my Datsun forklift--Nissan H20

Nissan Forklift Engine parts guides TIFFIN PARTS

Posted on Sep 13, 2015

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

TCM Forklift model FCG25-3L will not start when i turn the key to the on postion u can hear the fuel coming out of the intake

Danger of hydro-lock or fuel in crankcase condition will occur. Do not start! Fuel pump relay should be interlocked with oil pressure sending unit. Is it diesel or gas? Is it Carb or fuel injection? Investigate before running engine. Check oil dipstick for presence of fuel in oil. Fire hazard also exist .Be careful.

May 22, 2017 | Cars & Trucks

1 Answer

I have a TCM fg20 forklift that here lately seems like you have to give it more gas to move . It's propane powered. Any idea what to check ? Scott

all forklifts have an isolator valve in the drive system that stops the vehicle movement if the foot is on the brake
that area of control is where I would be looking at because if the valve is not allowed to neutralize properly then it stops movement or only allows partial movement

Dec 04, 2016 | Cars & Trucks

1 Answer

I have an old Datsun forklift with a Nissan H20 engine that won't start. I popped the distributor cap and the distributor is not turning when I crank the engine . What is broken?

Pull the distributor and check if the gear on end of dist. shaft is attached. The roll pin holding the gear may have sheared off.

If it is not the distributor, check the timing chain still works.

Sep 13, 2015 | Nissan Cars & Trucks

1 Answer

Holden engine 1961

The old holden grey motor will be difficult to source now but I would check places like GEM engines --repco engine reconditioners. The motor was also used in some early forklifts. Make calls to holden car clubs and see if they can source one for you. Try holden specialist wreckers. who have a network connection to otherl associated wreckers.

Apr 25, 2013 | Cars & Trucks

1 Answer

Can you please tell me timing chain set up for nissan navara 2.4 petrol motor year 1999

probably very similar to the early bluebirds or 180Bs..chain goes around all the sprockets,and kept tensioned by a oil pressured tensioner,.normally dont give any problems

Jun 29, 2010 | Cars & Trucks

1 Answer

We're trying to fill the water tank for the first time. on the outside, rear driver's side, there's a guage (pressure?) and to the right of it, there's a hole (for h20?). And what about a water pump?...

Dodge 400 motor home?, what is the year, is this a chassis conversion, if this was added on equipment then we have no information, u will need to contact the company that modified the chassis

Apr 29, 2010 | Dodge 400 Cars & Trucks

1 Answer

I cant locate the fuel filter on my 2005 1.5 petrol almera??? where is it???

the early models had the fuel filter mounted in the engine bay against the firewall. follow the fuel lines from the motor to the firewall. if there is no filter there then it is the late model and the filter is part of the fuel sender unit, this is mounted in the fuel tank and includes the fuel pump. this type is difficult to replace, and sometimes requires replacment of the entire sender unit.
Best way to tell is to call a nissan spare parts dept witn you VIN number and ask if this filter is replacable.

Aug 08, 2009 | Nissan Altima Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

77499 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides