Question about Ford Laser

Open Question

How to remove ignition barrell 1995ford laser

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3422 Answers

SOURCE: broken ignition barrel ford laser 1989 model

Hi,

this is the procedure to remove the ignition barrel:

Remove the steering column surround and you should see a black round thing on the left hand side, this is the ignition switch. Remove this and you will see there is one screw holding the ignition barrel on, remove and you then need to insert your key and turn it to the ACC position. you should now be able to withdraw the barrel using the key but take care not to snap the key off in the barrel.

Please don't forget to rate or accept the solution as fixya.

Goodluck..

Posted on Jun 15, 2008

mcgyver468
  • 710 Answers

SOURCE: Removal of the ignition Barrek

HAVE YOU TRIED TO USE SOME SILICONE SPRAY ON THE NUT? MAYBE YOU CAN CUT THE NUT OFF WITH A DREMEL AND A VERY SMALL DIAMOND BIT WITHOUT CUTTING THE DASH. HOPE THIS HELPS. LET ME KNOW. GOOD LUCK

Posted on May 03, 2009

  • 4 Answers

SOURCE: mercedez 190 ignition barrel. I have taken out ignition barrel attached to steering coloum but i can not remove key ignition from steering coloum how does it remove ignition barrel from steering

Should be the same as w123 model. Check diy Mercedes web page.
Photos included easy to do.

Posted on Jul 07, 2009

e-Guru
  • 3917 Answers

SOURCE: how to remove jammed ignition barrell from 1992,

Hi

you can access the ignition switch from underneath the dash, but it is easier to remove the steering wheel, then the instrument cluster. There are two basic elements to the ignition switch. The part that usually breaks down first is the front section, where the key goes into. You have to remove the entire unit from its bracket. Unplug the wire loom from the back of the housing. I believe there are two screws holding both sections together. Remove the screws and replace the unit. Then re-assemble.

Please check the link bellow :-

http://www.ehow.com/how_5833556_remove-mercedes-ignition-switch.html


Please accept the solution if it’s helpful. Do get back to us for any further query.
Thanks for contacting fixya.com

Posted on Sep 02, 2010

Geekman
  • 32281 Answers

SOURCE: I need to reprofile the ignition barrel on a 1985 1.6 Capri Laser

This needs a locksmith to carry out this work. The barrel has spring loaded slugs that match the shape of the key. We mortal do not have the equipment or the assortment of various slugs sizes to match the key so the barrels in all the locks are keyed alike..

Posted on Apr 20, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key broken in ignition barrel


Any parts store will have torx bits, this will remove the bolts.

Jan 12, 2014 | Ford Festiva Cars & Trucks

6 Answers

Broken ignition barrel ford laser 1989 model


you your self can do it its simple do not call an technician. i will definatly guide you just let me know from where it is exactly broken.

Jun 15, 2008 | Ford Laser Cars & Trucks

2 Answers

How do i take out my ignition barrel 98 vt


to remove you ignition barrel is a simple process you need to remover the steering column covers from around the ignition switch.
there is a small hole located in the ignition barrel you will need to gentle push and hold an Allen key in the hole and rotate the key to the accessories the barrel should be come lose and gentle be pulled out.
please note that if the internal locking mech is not correctly depressed you will not be able to remove the barrel.
also if you have lost you key you will not be ale to remove the ignition barrel and will need to get a lock smith to rplace the whole thing witch can cost from $120 up to $250 depending on the locksmith

Jan 02, 2013 | 1998 Holden VT Commodore

1 Answer

I need to reprofile the ignition barrel on a 1985 1.6 Capri Laser


This needs a locksmith to carry out this work. The barrel has spring loaded slugs that match the shape of the key. We mortal do not have the equipment or the assortment of various slugs sizes to match the key so the barrels in all the locks are keyed alike..

Apr 19, 2012 | Cars & Trucks

1 Answer

1995ford escortremove ignition lock


Very easy if you have the key and it turns. Put in the key and turn it to the run (not start) position. Look under where the lock cylinder is and there should be a small hole. You need to take a long narrow piece of steel to push in a concealed retaining pin by the lock cylinder. At the same time you push in the pin you pull outward on your key and the whole cylinder slides out. If there is no hole in the steering column for this you need to remove the covers.

Jan 29, 2012 | Cars & Trucks

1 Answer

I have an Isuzu Rodeo and the key is stuck in the ignition any idea how to get it out? Year 2000


replace the whole ignition barrel with new key and get key programmed by dealer
can remove barrel and key by removing steering column covers turn ignition to on position and with small shank screw driver push in hole in outer top rear section of barrel assembly then pull out ignition lock barrel with key in it. fit new lock barrel and key, program new key into system and can get door lock barrels coded to suit new key or get code for old key and cut new key so it fits mechanical locks on the rest of the vehicle (just wont turn in ignition) 2 keys for vehicle.

Jun 13, 2010 | 2000 Isuzu Rodeo

2 Answers

Key broken off in ignition barrel - how do I remove the barrel?


not saying it is landrover barrel but best way is get your new barrel and that should tell you how it is fitted normally a spring loaded pin holds barrel in socket

Mar 20, 2010 | 1994 Land Rover Discovery

1 Answer

I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING IN IGNITION BARREL NOW THE STEERING IS LOCKED ALSO I HAVE TAKEN OUT IGNITION BARREL WITH STEERING COLOUM. i WOULD LIKE TO DISINGAGE THE IGNITION BARREL...


it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

May 19, 2009 | 1993 Mercedes-Benz 190

2 Answers

Removal of the ignition Barrek


HAVE YOU TRIED TO USE SOME SILICONE SPRAY ON THE NUT? MAYBE YOU CAN CUT THE NUT OFF WITH A DREMEL AND A VERY SMALL DIAMOND BIT WITHOUT CUTTING THE DASH. HOPE THIS HELPS. LET ME KNOW. GOOD LUCK

May 03, 2009 | 2005 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...