Question about 2003 Jeep Grand Cherokee

1 Answer

2003 jeep grand cherokee,had to replace window regulators in 2 doors took the door apart and disconnected battery while waiting on parts,about a that thats done gauges flicker all kinds of noises and wont start.pretty sick of all the problems with this car.just disconnecting the battery causes problems?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,071 Answers

Disconnct negative terminal and reconnect lock and unlock driversw door with the key

Posted on Jul 21, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to install power window cable

cable? (electric>?)
here is the page on motor;reg.
  1. Disconnect and isolate the battery negative cable.
  2. Remove the window regulator from the door.
    • Remove door trim panel.
    • Remove isolator.
    • Remove front door glass.
    • Loosen bolts attaching regulator to inner door panel.
    • Remove bolt attaching regulator to inner door panel.
      • Lift regulator upward to disengage bolts from door inner panel.
      • Disengage power window regulator harness connector, if equipped.
      • Remove regulator through access hole in door
    • Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
    • Remove the power window motor from the window regulator.

Jul 04, 2014 | 2000 Jeep Grand Cherokee

2 Answers

Window on right side dont work on 2002 jeep grand cherokee

if its electric a fuse could be bad or a shortage in the wiring

Nov 06, 2012 | 2002 Jeep Grand Cherokee

1 Answer

I would like to dismantle the driver side door on my jeep grand cherokee to replace the window regulator. The manual does not go into enough specific detail to dismantle the door. Please help.

Welcome to the club! You now have a small taste of what it is like to be a professional automotive technician. Not only do most service manuals not give detailed instructions on how to do this, but almost every make and model of car out there comes apart differently....But we auto techs are supposed to just know all this stuff....

Anyway, The first thing you have to do is get the door panel off without destroying anything. This is the toughest part - I have seen many door panels that flop like a flag in the wind because they got busted-up by someone trying to get a window working.

This should work on your Jeep:
Remove the plug from the mirror flag bezel. Remove trim panel attaching screws. (There is usually 4 of them - check all around the perimeter and check for one near the door handle) Once you are sure you have all the screws removed, use a trim panel tool (Available at your local parts store) to pop the push-clips loose from around the perimeter of the door panel. BUY THE TOOL! It is not very expensive and It will save you from breaking your door panel to pieces so it won't stay on any more!
Once the clips are popped loose, Lift up on the door panel to release the hooks and pull the door panel out slightly. Disconnect all wiring connectors. Disconnect the latch rods from the inside handle actuator. Remove the door panel.
After the door panel is removed, remove the inner and outer belt weather strips.
Remove the door insulator. Remove the clips that attach the glass to the lift plate. Push the bottom of the glass outward and the regulator lift plate inward to disengage the studs. Push upward on the glass and lift the glass from the door. Remove the regulator-to-door bolts. Move the regulator so the electrical connector can be disconnected from the window motor. Remove the regulator through the access hole.

Reverse procedure to install.

Apr 19, 2011 | 2000 Jeep Grand Cherokee

1 Answer

How do i replace a window regulator

the door panel will have to be removed along with disconnecting some electrical connections for your door switches, regulator is on the inside of the door, if you get confused , get a manual for your vehichle at a auto part store, or go to a library and look it up and make copy of it to refer by. i would also disconnect the negative battery cable before starting this procedure , to make sure nothing electrical goe's wrong while replacing regulator. after regulator is replaced , you will have to reset all radio, and etc functions.

Feb 11, 2011 | 2000 Jeep Grand Cherokee

1 Answer

I need instructions on how to replace power window motor for the front driver side window of a 2002 Grand Cherokee

Power Window Motor: Service and Repair
1. Disconnect and isolate the battery negative cable.
2. Remove the window regulator from the door.
3. Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
4. Remove the power window motor from the window regulator.
1. Position the power window motor onto the window regulator.
2. Install and tighten the screws that secure the power window motor to the window regulator. Tighten the screws to 9 Nm (80 in. lbs.).
3. Install the window regulator onto the door.
4. Reconnect the battery negative cable.

Oct 30, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Remove/replacing side view mirror on a jeep grand cherokee

    Remove the Old Mirror
  1. Step 1 Disconnect the negative battery cable before you take off the grand Cherokee front door trim panel. Remove all screws and clips.
  2. Step 2 Detachthe window trim cover screw, and control lever screw beforedisconnecting the entire mirror trim cover. Remove the rubber coverinside the mirror cover, and disconnect the electrical wire.
  3. Step 3 Remove three nuts from the power mirror using a Torx® star-shaped screwdriver.
  4. Step 4 Pull out the outside rear view mirror. Guide the power wire through the hole in the door.
  5. Install the New Mirror
  6. Step 1 Replace the old mirror. Put the new power mirror in place. Push the new wiring through the hole in the door.
  7. Step 2 Install and tighten the three retaining screws you took off when removing the old mirror.
  8. Step 3 Connect the power mirror wiring to the connection located on the door panel. Replace the rubber cover and interior mirror cover.
  9. Step 4 Put the front door trim panel back in place by securing all clips and tightening all screws.
  10. Step 5 Connect the Subaru Outback's battery cable to restore the power.

i will recommend i site where you will get all the information you need to remove and replace your side mirror

Sep 10, 2009 | 2004 Jeep Grand Cherokee

1 Answer

2002 jeep cherokee right window regulator replace

The short course is:

- disconnect negative battery cable

- remove door panel

- disconnect motor wire harness

- drill rivets from from motor mount

- install new motor with pop rivets (need a gun) or screws

- etc.

If you need more info on how to do these things, let me know.


Aug 31, 2009 | 2002 Jeep Grand Cherokee

1 Answer

1993 Jeep Grand Cherokee Lorado - window tipped, roller broken

If the motor still actuates and moves when activated then no replacement is required. When the roller cracked it may have however burnt out the motor. replacing the roller and realigning the window is very easy.. the parts.... go see your local auto wrecker. they may be able to sell you a roller or 2 from a wrecked cherokee(and maybe pick up a spare motor while you're at it. This is usually the cheapest solution for parts.

Jul 04, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

How to take a door panel apart

check the fuse box and make sure the windows are not fused separately,before taking the door apart.
the door panel is held in with clips and there is a tool made for removing them.the window regulator/motor is a tricky one to do and unless you are really good,do not mess with it.
the motors have internal thermal cutouts.

May 08, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Electric Window cable connections

unfortunatly there is no diagram or actual repair for a window regulator. the only fix is to replace the regualtor assembly. ive replaced hundreds of them at the jeep/chrysler/dodge dealer i work at

Jan 05, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2003 Jeep Grand Cherokee Logo

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides