Question about Cars & Trucks

Open Question

Cleaner assembly i'snt working - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need help finding my map sensor


your map sensor on the intaque manifom .when you change your map sensor you have inprestion the motor runing bedter because prestion your car need to run if snt that check your oxygen sensor ,or cank sensor end check ,catalitic muffler if is nut stuck ... mike66

Mar 04, 2013 | Cars & Trucks

1 Answer

Where is the engine computer located on the 97 cadillac eldorado?


To Remove:
  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section.
  2. Record the Transaxle Fluid and Engine Oil Life Indexes
  3. Remove or disconnect the following:
    • The negative battery cable gm_car_cad_sev_intk_air_duct_resontr.gif

    • The screw retaining the intake air duct/resonator (C) to the PCM housing gm_car_cad_sev_air_clenr_cov.gif

    • Air filter housing clamps on top of the air cleaner housing assembly
    • Intake air duct/resonator assembly (B) partially up and remove the air cleaner cover (C) and the PCM
    • Air cleaner element assembly, slide toward the fender to separate the air cleaner element assembly from the air inlet assembly gm_car_cad_sev_pcm_rem.gif

    • PCM connector attaching bolts
    • Two PCM connectors
    • PCM (A)
To Install:
NOTE: If the PCM is being programmed using the Off-Board method, perform the programming before continuing with the steps listed below.
  1. Install or connect the following:
    • PCM
    • PCM connectors; torque connector screws
      1. Torque to: 71 lb-in. (8 Nm)
    • Air cleaner cover onto the air inlet housing
    • Snap the assembly clamps into place
    • Align the intake air duct/resonator assembly
    • The screw onto the intake air duct/resonator assembly
      1. Torque to: 27 lb-in. (3 Nm)
    • Connect the negative battery cable
  2. Program the PCM, if required.
prev.gif next.gif

Jan 28, 2011 | 1997 Cadillac Eldorado

1 Answer

Where is the transmission deep stick?


under the air cleaner

jturcotte_22.jpg

Checking the Fluid Level

 Park your vehicle on a level place. Keep the

engine running.

 With the parking brake applied, place the shift lever

in PARK (P).

 With your foot on the brake pedal, move the shift

lever through each gear range, pausing for about

three seconds in each range. Then, position the shift

lever in PARK (P).

 Let the engine run at idle for three to five minutes.

Then, without shutting off the engine, follow these steps:

1. The black transaxle fluid cap is located next to the

radiator hose and below the air cleaner assembly on

the driver's side of the engine. Remove the air

cleaner assembly so you can reach the transaxle fluid

cap. The assembly is attached to the vehicle by two

fasteners. Lift up on the air cleaner assembly to

remove it. Find the transaxle fluid cap and turn it

counterclockwise to remove. Pull out the dipstick

and wipe it with a clean rag or paper towel.

2. Push it back in all the way, wait three seconds and
then pull it back out again.

Nov 15, 2010 | 1998 Cadillac DeVille

1 Answer

How do i install a master air flow sensor and where is it located and how long does it take and cost for the part?


It depends on which engine you have, but can be done in about 30 minutes in each case. I have pasted the procedure from autozone.com below. The cost is $200.


REMOVAL & INSTALLATION

2RZ-FE and 3RZ-FE Engines
See Figure 2

  1. Disconnect the MAF harness and the IAT harness along with the wire clamps.
  2. Loosen the are cleaner hose clamp.
  3. On the 3RZ-FE, disconnect the air hose from the air cleaner cap.
  4. Loosen the four clips, then the air cleaner cap with the meter attached.
  5. Remove the four nuts, MAF meter and gasket from the cap.

ff0d559.gif

Fig. Fig. 2: Exploded view of the MAF meter on the 2RZ-FE and 3RZ-FE engines

  1. Discard the gasket.

To install:
  1. Place a new gasket on the air cleaner cap.
  2. Install the MAF meter and tighten the nuts to 74 inch lbs. (8 Nm).
  3. Install the meter and cap assembly on the air cleaner housing.

5VZ-FE Engine
See Figure 3
  1. Disconnect the air cleaner cap from the MAF meter.
  2. Detach the harness from the meter.
  3. Remove the mounting bolts for the meter. Lift off the meter and discard the gasket.


ad21d4c.gif

Fig. Fig. 3: Remove the bolts securing the meter

To install:

  1. Place a new gasket in position, then tighten the meter to the cap assembly, 61 inch lbs. (7 Nm).
  2. Attach the meter and cap assembly to the air cleaner housing.

1FZ-FE Engine
  1. Disconnect the MAF meter harness and wire clamps.
  2. Separate the cruise control actuator cable from the unit.
  3. Loosen the air cleaner hose.
  4. Disconnect the 3 clips, then remove the wing nut, air cleaner cap and meter assembly.
  5. Unbolt the meter from the cap. Discard the gasket.
To install:
  1. Secure the MAF meter to the cap with a new gasket.
  2. Install the cap/meter assembly to the air cleaner housing.
  3. Attach the air cleaner hose to the unit.
  4. Attach the cruise control actuator cable.
  5. Connect the MAF meter harness and wire clamps.

Oct 28, 2010 | 1994 Toyota Pickup

1 Answer

Cannot find thermostat of 99 Lexus ES300


1999 Lexus ES300 (3.0L, VIN F, 5th digit, 1MZFE engine)

Thermostat on 1mz-FE Engine
  1. Disconnect the negative battery cable. Wait at least 90 seconds before performing any other work.
  2. Drain the engine coolant.
  3. Remove the battery.
  4. Remove the air cleaner inlet assembly.
  5. Remove the air cleaner assembly with hose.
  6. Remove the air cleaner bracket.
  7. Remove the air cleaner inlet No. 1.
  8. Disconnect the radiator hose outlet.
  9. Remove the bolt and water inlet pipe.
  10. Remove the O-ring from the water inlet pipe.
  11. Remove the 3 bolts and water inlet.
  12. Remove the thermostat.
9b08ecc.jpg

Fig. Correct alignment of the thermostat jiggle valve.-1MZ-FE and 3MZ-FE engines

Hope helps (remember to rate and comment this).

Sep 30, 2010 | 1999 Lexus ES 300

1 Answer

How long does it take to change a water pump in a 2002 SL Saturn


Hi. Normal installation would take 45 to 1 hour depends on your expertise. Here's the procedure on how to replace the power pump.

  • TOOLS REQUIRED
  • J-43651 Water Pump Sprocket Holding Tool
REMOVAL



  1. Disconnect negative battery cable.
  2. Remove air inlet tube and air cleaner assembly. Refer to "Air Cleaner Assembly Removal".
  3. Drain coolant.


  1. Remove exhaust manifold heat shield. IMPORTANT: Twist water feed pipe while pulling to remove it from water pump.


  1. Remove thermostat and water feed assembly bolts.


  1. Remove water pump sprocket access plate from front cover.


  1. Install J-43651 water pump sprocket holding tool. IMPORTANT: Be sure to remove retaining bolt that is accessed from front of engine block.


  1. Remove water pump retaining bolts.
  2. Remove water pump assembly.
INSTALLATION

NOTICE: Prior to installing the water pump read the entire procedure. Pay special attention to avoid part damage and to ensure proper sealing.



  1. Install water pump assembly.
  2. Install water pump bolts. Initially finger tighten bolts
  • Torque: 25 Nm (18 ft. lbs.)



  1. Install the water feed tube.
  2. Lubricate the feed tube O-ring with silicone gel lubricant.
  3. Install water feed tube by twisting and pushing toward water pump. Take care not to tear or damage the O-ring.
  4. Install thermostat housing to block bolts.
  • Torque: 10 Nm (89 inch lbs.)



  1. Install exhaust manifold heat shield.


  1. Install air cleaner assembly and air inlet tube. Refer to "Air Cleaner Assembly Installation".
  2. Connect negative battery cable.
  3. Add coolant.

Aug 27, 2010 | Saturn LS Cars & Trucks

1 Answer

Where can i locate the starter


Hi,
Remove the air intake hose from the air cleaner assembly. Remove the clamp and then pull the hose straight off the assembly. Remove the wing nut securing the air cleaner by turning it counterclockwise by hand. Remove the air cleaner.


You will Locate the starter motor directly below the air cleaner assembly. Disconnect the wiring connection on the starter motor. The plug should pull straight out from the connection. Remove the nut securing the starter wire using 13-millimeter socket and ratchet and remove the wire.

Have a nice day

Aug 03, 2010 | 1994 Nissan Sentra 4-Door

1 Answer

My blower does´snt work neither can we seem


if you near alicante pop in and i will do it free ,the switch in the middle needs changing its a common fault and fairly easy to do ,also the blower motor could need new brushes ,the AC will not work if the blower doesnt work .but more often than not its the switch

Mar 17, 2010 | 1997 Ford Escort

2 Answers

2003 hyundia accent 1.6


The MAF is mounted in the intake air hose of the air cleaner assembly.
The MAF is mounted in the intake air hose of the air cleaner assembly.
The MAF is mounted in the intake air hose of the air cleaner assembly. On some vehicles this sensor is combined wit the ATS sensor.
The MAF is mounted in the intake air hose of the air cleaner assembly.
This sensor is located in the air intake plenum assembly. It is combined with the IAT sensor.
The MAF is mounted in the intake air hose of the air cleaner assembly. On some vehicles it is combined with the IAT sensor.

Oct 08, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...