Question about 1983 Jeep CJ7

1 Answer

WHAT ID THE BELLHOUSING CLUTCH BOOT OEM NAME?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 850 Answers

Clutch fork boot

Posted on Jul 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

S10 4.3 vortec 1996 slave cylinder replacement, cracked oil pan, pressure plate came apart broke part of bellhousing. Anyone ever have this problem?


I have never seenthis type of failure on this site in the 6 years I have been answering question here, sounds like the clutch exploded, did you have a factory OEM unit in it?

Oct 15, 2016 | Cars & Trucks

2 Answers

My scania 124L. I change the clutch plate. Have no clutch , I cant see the bleeding niple.


Some don't have a bleeder. You just have to pump the pedal till the pressure builds up.

Aug 28, 2016 | Cars & Trucks

2 Answers

1996 Bronco manual transmission hard to shift


You have a m5 (mazda 5 spd) transmission. Same thing that is in my 96 f150 4x4.

Ford had a problem with the slave cyclinders on thoes trannys. The slave is mounted inside the bellhousing and wraps aroung the input shaft, eliminating the need for a fork.

I am willing to bet my next paycheck that you have brakefluid inside the bellhousing.

Ford has a revision on that slave cylinder. because there is no dust boot on it, clutch material gets to the seal and tears it up, and because of the heat the seal will fail.

Replace your clutch, Flywheel (will have brake fluid burned into it), Slave cylinder, and possibly the line going to the slave (sometimes the realease locks up).

Make sure you get the slave from FORD, it is around $100.00, about 2x as much as anyone else but well worth it. I have not found anyone but ford make it with the boot and upgraded seal. If you get one from a parts store it will only last about 3 months. I tried, first one went out in 3 months, had it warrentied, then second only lasted 2.5 months. I finnaly brokedown and paid the extra for a FORD and it at 11 months it is still going strong.----------------------------------------------------
Launch X-431 IV Auto Scanner

Mar 14, 2013 | Ford Bronco II Cars & Trucks

1 Answer

Pt cruiser clutch diagram


I recommend bleeding the clutch using instructions pasted from autozone.com below. As for the engine light, please get the computer scanned and send us the diagnostic trouble code.
Hydraulic System Bleeding NOTE
It is necessary to bleed the clutch hydraulic release system if the system has lost an excessive amount of fluid and has allowed air into the circuit. Air in the system typically results in a spongy pedal feel, and/or improper clutch release. If air cannot be removed from the system using this procedure, it is necessary to replace both the clutch master cylinder and slave cylinder assemblies.

Except Turbocharged Models
  1. From driver's seat, actuate clutch pedal 60-100 times. Verify clutch operation/pedal feel. If pedal still feels spongy, or clutch does not fully disengage, excessive air is still trapped within the system. Perform the following procedure:
  2. Verify fluid level in clutch master cylinder reservoir. Top off with DOT 3 brake fluid as necessary.
  3. Raise and safely support the vehicle.
  4. Remove clutch slave cylinder assembly from the transaxle case, but do not disconnect from the system. Allow the slave cylinder hang, making it the lowest part of the system.
    CAUTION
    While slave cylinder is detached from the transaxle, DO NOT actuate the clutch master cylinder. Damage to the slave cylinder will result.
  5. Depress slave cylinder pushrod until it bottoms and then release. Repeat this at least ten times, forcing trapped air upwards and out of the system.
  6. Re-install slave cylinder into position. Torque slave cylinder to case bolt to 168 inch lbs. (19 Nm).
  7. Carefully lower the vehicle.
  8. Check and adjust clutch master cylinder fluid level. Actuate clutch pedal thirty (30) times. Verify clutch operation/pedal feel. If pedal still feels spongy, or clutch does not fully disengage, air is still trapped within the system. Repeat Step 3 through Step 7 until air is purged. If several attempts at purging air from the system are unsuccessful, replace both the clutch master cylinder and slave cylinder assemblies.
  9. Raise and safely support the vehicle.
  10. Carefully lower the vehicle.
  11. Top off clutch master cylinder fluid level with DOT 3 brake fluid as necessary.
Turbocharged Models

NOTE
Due to the angle and design of the turbo hydraulic system components, gravity and pedal bleeding are less effective and less efficient than the reverse fluid injection method (reverse bleeding). Reverse bleeding is recommended for this system, and requires the use of commercially available injection bleeding equipment.

Alternate Procedure (Pedal Bleeding)
  1. Remove reservoir cap and inspect fluid level. Top off with DOT 3 Brake Fluid. Actuate clutch pedal briskly at least 50 times. Verify release system function. Repeat. If release system is still inoperative, continue with procedure.
  2. Raise and safely support the vehicle.
  3. Remove clutch bellhousing access cap to expose system bleed screw.
    WARNING
    Use care not to allow fluid to drain into clutch bellhousing. Excessive fluid will be agitated and sprayed around inside the clutch bellhousing by the rotating flywheel, contaminating the flywheel, disc, and pressure plate, resulting in poor clutch engagement.
  4. Using suitable socket/wrench, loosen bleed screw. Immediately install rubber hose to bleed screw to prevent fluid from entering clutch bellhousing. Tighten bleed screw gently with suitable wrench.
  5. Lower vehicle.
  6. Have helper actuate clutch pedal to floor.
  7. Place collection container at end of hose to capture expelled fluid.
  8. Using suitable wrench, break bleeder screw loose and tighten to 62 inch lbs. (7 Nm). Do not over-tighten.
  9. Have helper release pedal, returning it to at-rest position, and then actuate pedal to floor.
  10. Break bleeder screw loose and tighten to 62 inch lbs. (7 Nm). Do not over-tighten.
  11. Repeat procedure as necessary, keeping master cylinder reservoir full during the process, until air bubbles are no longer visible in collection container.
  12. When air bubbles are no longer visible, actuate clutch pedal briskly at least 50 times.
  13. Verify release system function and top off fluid as necessary.
Recommended Procedure (Reverse Bleeding)
  1. Remove reservoir cap and inspect fluid level. Top off with DOT 3 Brake Fluid. Actuate clutch pedal briskly at least 50 times. Verify release system function. Repeat. If release system is still inoperative, continue with procedure.
  2. Remove reservoir from bracket and empty into collection container.
  3. Raise and safely support the vehicle.
  4. Remove clutch bellhousing access cap to expose system bleed screw.
    CAUTION
    Use care not to allow fluid to drain into clutch bellhousing. Excessive fluid will be agitated and sprayed around inside the clutch bellhousing by the rotating flywheel, contaminating the flywheel, disc, and pressure plate, resulting in poor clutch engagement.
  5. Using suitable socket/wrench, loosen bleed screw.


    Fig. Location of the bleed screw for the 2.4L engine
  6. Quickly attach hand operated bleed apparatus to bleed screw. Use care not to over-fill reservoir and spill fluid into engine compartment.
  7. Operate bleed gun sufficiently to expel air upward through circuit and out of master cylinder reservoir. Fill and empty reservoir three times.
  8. Remove bleed apparatus and tighten bleed screw to 62 inch lbs. (7 Nm). Do not over-tighten.
  9. Carefully lower the vehicle.
  10. Top off reservoir with fluid, then return the cap.
  11. Verify system operation. Actuate clutch pedal 50 times. If necessary, repeat procedure until road test confirms that shift issues no longer exist.

May 20, 2017 | 2002 Chrysler PT Cruiser

2 Answers

The transmission is a 5 speed and its 2 wheel dr 93 Jeep Cherokee Sport.Where is the slave cylinder in the transmission located?


There are two versions...the easiest to work on is located on the drivers side of the bellhousing. The other version is inside the bellhousing and is part of the throwout bearing (there will be a hose connection going into the bellhousing and a bleed valve protruding from the side of the bell housing on those) This version is used on later models but I have seen it used when engine/trans swaps have been previously made. Clutch master is on the firewall on the left side of the brake master cyl.

Oct 16, 2009 | 1993 Jeep Grand Cherokee

1 Answer

How to pull out tranny and fix TO bearing on a 97 mustang v6. 5 speed thanks alex


start by removing the the shifter lever and boot, next remove the drive shaft,then remove clutch cable or hydraulic line for throw out fork,it may be neccessary to remove y-pipe and some of the exhaust using a transmission or floor jack support transmission and remove crossmember, remove bellhousing bolts and transmission should now be free to remove.

Jul 18, 2009 | 1999 Ford Mustang Cobra

1 Answer

91jeep clutch quick pedal loss, barely shifts


Look inside the vehicle at the firewall where the clutch pedal rod goes into the master cylinder. See if there is fluid running down the inside firewall. Next look at the bottom of the bellhousing to see if fluid has been coming out of it. That will tell you if it's the master or slave cylinder. Most likely it is the slave leaking inside the transmission bellhousing.

Jun 07, 2009 | 1991 Jeep Wrangler

1 Answer

Clutch problem


Dry clutch res. is generally caused by a leak either in the clutch master cyl or the slave unit on the bellhousing. check both for leaks and replace as needed. Master will show seepage between unit and firewall... slave will have fluid under rubber dust boot. Make sure youbleed it (just like brakes) after you replace either.

Nov 02, 2008 | 2004 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...