Question about Cars & Trucks

Open Question

I have a powertrain rvc800 instailed on my car and van I have just bought a 4wd that did not have reverse camera and i want to swap it over and add a camera to the 4wd and another trailer

I bought rvct1 and rvc-1 to fit to the 4wd and trailer the wiring on the rvc800 has 4 wires red, black and yellow with a second yellow in the main yellow sheath between the camera and monitor the rvct1 and rvc-1 only have 3 wires red, black and yellow and the plugs are different types. Do you have a soution to mate this all together. Thanks. Bob

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Trailer Connections

I took the vehicle to Bosch, an electrical expert in Germany.

Posted on Jun 29, 2008

  • 360 Answers

SOURCE: No Start, No Spark, for Grand Caravan 3.8L

we get remans bad out of the box......... good luck

Posted on Sep 26, 2008

  • 111 Answers

SOURCE: 2007 Chevy Express Trailer Wiring

on most new trucks there is a wiring harness that has a cover over it that you plug a extension into. Look for that first. If you can't find it I would go to the dealer and ask them to make sure that you don't cut wires you don't have too and end up with a mess.

Posted on Mar 14, 2009

  • 17 Answers

SOURCE: o2 sensor wiring diagram

A new 02 sensor will come with new wires and connector. If not get back with me I think there is a repair kit for that problem.

Posted on Jun 01, 2009

  • 1 Answer

SOURCE: My dog chewed off the trailer + car wiring plug

Found this on the Wb


Posted on Sep 14, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2006 wrench light is on

Powertrain Malfunction (Wrench) Warning Indicator (base instrument cluster)
The instrument cluster receives the powertrain status from the PCM over the high speed CAN. When a powertrain system concern is detected, the PCM sends the instrument cluster a command signal to illuminate the powertrain malfunction (wrench) warning indicator. If the 4WD control module detects a failure with the 4WD drive system, the 4WD control module sends a message to the instrument cluster over the CAN to illuminate the powertrain malfunction (wrench) warning indicator. On 4.6L engines, if the transmission control module (TCM) detects a failure with the transmission, the TCM sends a message to the instrument cluster over the CAN to illuminate the powertrain malfunction (wrench) warning indicator.
better have it checked !

Sep 10, 2016 | 2006 Mercury Mountaineer AWD

1 Answer

1998 ford explorer 4.0, 4wd, goes good forward ,no reverse


It could be for a few reasons but a problem with the transfer case causing loss of reverse is quite common on these vehicles. It is an early symptom of a problem which is only going to get worse unfortunately.
To get it working for now try shifting in & out of 4WD high & low a few times, trying to reverse each time. Hopefully this will enable reverse to engage again (make sure you are driving on an unsealed surface if you are turning while using 4WD low.)
If the problem is what I suspect it is you will have to either rebuild your tranny or swap it out for a good one. If you are lucky you will be able to pick one up for about $150 from a vehicle being wrecked.
Normally the gearbox is still good unless this problem has been left untended for a long time.


Jun 17, 2014 | 1998 Ford Explorer

1 Answer

I have a 2003 dodge ram 1500 cargo van, my turn signals do not work, I change the flasher twice.

I would have to assume that there is a relay or two on the flashers to be able to separate the emergency flasher from the signals, and the marker lights from the brakes etc. Replace the relay or swap with another one to test.

Nov 12, 2013 | 1998 Dodge Ram 1500 4WD

1 Answer

05 trailblazer EXT shutters and bucks in 4WD

If you are engaging 4wd on paved road, the powertrain or drive train will bind and cause a "bunny hop" condition. It is usually worse when making turns. Make sure you never engage the 4wd on hard dry surfaces, you will damage it.

Nov 03, 2011 | 2005 Chevrolet Trailblazer Ext

1 Answer

Just bought a 4wd 07 chevy tahoe LT. Was spinning out in reverse on a sheet of ice and only the rear wheels moved. did it a few times and got same result. Is the car just not 4wd in reverse? Thank you...

WERE YOU in auto 4wd or 4hi? sometimes vehicles will pop out of 4wd in reverse the auto mode detects slip going forward not backwards so if in auto tes it will have problems in reverse.

Dec 22, 2010 | 2007 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides