Question about Cars & Trucks

1 Answer

It is getting spark but it seems that there is no fuel pressure at the stem on the fuel line.how can I be sure it is the fule pump and not the relay or anything else. I have checked the fuses.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 13,017 Answers

Hook up a fuel pressure gauge ! Go on youtube and watch videos on fuel pump electrical circuit testing ! Do you know how to use a DVOM - digital volt ohm meter . Find a wiring diagram at www.bbbind.com . Look at diagram to see what controls the fuel pump , relay , a control module etc.... If there is a relay ,pull it out an try to jump fuel pump directly .

Posted on Dec 05, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My stem has 2 fuel pump relays 1 of them gets hot does this mean that my fuel system is not woeking properly


If the relay is hot to the touch that means that the actuating coil is burning out and not closing the circuit for the fuel pump or the fuel pump is shorting out and the points in the relay are getting hot. Test the units with a multimeter.

Oct 06, 2014 | Cars & Trucks

1 Answer

Would this problem be a modular or fuel pump. We have changed the modular once with a used one. Now we have changed the fuel filter and there seems to be noise coming from the fuel pump (which we were...


Thanks for choosing FixYa and welcome to the site. You have a small port on your fuel rail on the engine that you test fuel pressure at. It almost looks like the valve of your tire. You test the pressure there. You may have a leaking fuel injector or pinched gas line since the filter and pump are working. If you have a fuel pump reset button, try that. Check your fuel pump fuse and relay just to be sure.

Apr 22, 2011 | 1992 Chevrolet Corsica

2 Answers

89 ford probe wont start, engine cranks , battery charged, inverta switch seems ok have continuity between switch, check ingnition coil - ok , spark in # 1 spark plug , check all fuses - ok , fuel...


Check for fuel pressure on the fuel rail while turning the key to start,if there is fuel pressure(enough)then the injectors are not pulsing(allowing fuel into the intake).The pick up coil in the distributor,will be the problem,unless it is distribuless ignition,then the cam sensor would be at fault.

Jan 22, 2011 | 1994 Ford Probe

1 Answer

I have a 1998 ford wind star new fule pump but still not geting fule , wont crank engine turns ove but won;t start


INSTALL PRESSURE GUAGE THEN CK, VOLTAGE TO PUMP PCM TURNS ON PUMP RELAY FOR 2 SECONDS WHEN KEY CYCLED ON ,, IF NO POWER CK INERTIA SWITCH ( MAY BE TRIPPED ) IF NO POWER TO INERTIA SWITCH CK FUEL PUMP RELAY IF NO VOLTAGE AT PUMP RELAY THEN CHECK FOR SPARK AT PLUGS IF NO SPARK CK PCM POWER RELAY IT SUPPLIES VOLTAGE TO PCM THAT INTURN POWERS FUEL PUMP RELAY

HOPE THIS HELPS

Aug 08, 2010 | 1998 Ford Windstar

1 Answer

My 2003 malibu with turn over but not start fule pump is getting 55 lbs of pressure at filter and rail if you spray start fluid in it it will start and run until it runs out of start fluid could this be a...


Signs of a Bad Fuel Pressure Regulator
the vehicle will not start, if a bad regulator. Usually, this is a problem that is encountered in the morning when you start your vehicle. Many a times, the engine starts, but stalls shortly after starting. check the fuse and relay for pump. also remove line to fuel pressure regulator and if fuel in line, replace fuel pressure regulator. check for spark and also the timing belt. its one sign of not starting. if car runs fine on spray, I would not say its the timing belt or chain.

Aug 05, 2010 | 2003 Chevrolet Malibu

2 Answers

Need to change fuel pump for 99 chevy blazer how do i do it and where is the fuel pump located


first you need to relive the fule system of pressure. do this by finding your fule pump relay disconecting it and start the car. it will sputer, this is reliveing fule pressure.once it stops sputering your ready to get the fule pump out. it is located in the fule tank. the tank is held on by 2 straps your going to have to take off. once you do that drop the tank and the pump will be on top of it.

Feb 20, 2010 | 1999 Chevrolet Blazer

1 Answer

98 merc tracer wont turn over....please helpme...


when tracers stop out of the blue like this, it can be a number of things. #1 is fuel pump failure or pump relay, or fuse. check to see if there is perssure at fule rail. check fule pressure regulator. #2 is ignition coil failure, or no spark. check plug wire from coil for spark. that will get you going in right direction. good luck.

Jul 12, 2009 | 1998 Mercury Tracer

3 Answers

My bmw has no fire and the fule pump does not come on


Check your fuse and the fuel pump relay.

May 24, 2009 | 1987 BMW 3 Series

2 Answers

The fule pump was not workin well we fix it but the car still ant geting fule


Have checked the fuel pump fuse how about the main relay. Have you tried checking and testing that? If you need instructions on how to test it let me know.

When you turn the key to access. II You hear the fuel pump run if you listen through the gas cap.

If the fuel pump is working I wouldnt assume it is a has problem yet.
I would start by checking spark make sure you are getting spark. Then make sure you are getting air. I would undo the intake pipe at the throttle body.

Once you done this let me know what happens.

Dec 13, 2008 | 1987 Honda Accord

2 Answers

Engine cranks but doesn't start, if i spray fuel on the intake will start, i can heard the fuel pump working when I open the ignition


I had two similar probs with a blazer 4.3L the fule pump runs but with not enough pressure to start the engine you must have more fule pressure to start the engine than to keep it running.
also there is a rubber seal connecting the pump to the line in side the tank if the rubber ripped or cracked it fits your situation.
take the rubber out and rig it with a piece of 100 psi fule line and a couple og stainless steel gear clamps instead of buy ing all the expensive items. good luck.

Jul 22, 2008 | 1992 Chevrolet Astro Extended

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...