Question about Mazda Cars & Trucks

1 Answer

Trying to install a thermostat in a 1986 mazda B 2200, thermostat keeps slipping down. How do I keep the thermostat from slipping down when I am tightening the housing back into place?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 76,846 Answers

Put a little bit of gasket cement or contact cement on the edge of the T-Stat to hold it in place.

Posted on Dec 05, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car a Mazda 2.0lt 1986 model keeps on overheating during a jurny we overalled the head and fitted a new head gasket but it keeps on overheating what's wrong


When you replaced the headgasket did you ensure that there were no cracks in the head? I know you say it was overhauled, just trying to cover all the bases. Did you change the thermostat when you replaced the headgasket? Is your radiator plugged or possibly your heater core. Start the car with the rad cap off and watch as it warms up. Once engine gets to temperature you should be able to see the fluid move in the radiator. If it overheats before that happens then your thermostat is sticking.

Nov 07, 2016 | Mazda Cars & Trucks

1 Answer

Will a 1990 ford ranger engine fit 1990 Mazda B 2200 truck without any modifications?


No it will not. Only a comparable engine from another mazda b2200 truck and I think the b2000 and possibly Miata, 2.2 engines were about the same from 1986-1993. You can pretty much count out just dropping in a motor from a different manufacturer for any make. Fords don't fit chevys, etc. etc., This would require you modify the entire drive train and quite possibly the electrical system, cooling system,etc. Definitely not worth the hassle involved.

Jul 22, 2014 | 1990 Mazda B-Series

1 Answer

Toyota repair manual 1992 hilux surf ssr-x


Hi. it could either be engine lacking power ie fuel or fuel pump,
rings,compression down,brakes binding,timing no vacuum advance working, or clutch slipping.

May 23, 2014 | 1986 Toyota Hilux 2200

2 Answers

How to change a thermostat in mazda protege 2003


2_28_2012_3_28_55_am.gifThe lower radiator hose follow it to the engine block You woll remove 2 bolt 12mm or 14mm. there you pull out the thermostat. when you install you need a new thermostat gasket.The thermostat has a air bleeder nipple that has to be up. When you fill the radiator and you start the vehicle the thermostat will open up when it is warmed and coolant will sink down there you fill the radiator up always keeping you eye on the temperature gauge. Also fill the resovoir.2_28_2012_3_34_36_am.gif

Feb 28, 2012 | 2003 Mazda Protege

2 Answers

If air conditioner system not working cause 1999 Mazda 626 2.0L to overheat


No this wont cause an overheat problem. Check the coolant level , check to see if the fans come on after it heats up. when the car is warming up you can check the thermostat, by touching the top radiator hose, after a few minutes the hose should get hot, this indicates that the thermostat opened up and is working. If it doesn't replace the thermostat. If it doesn't over heat until you start driving , then suspect the water pump. The impellers can slip on the shaft and not have enough flow to keep it cool.

Aug 26, 2011 | 1999 Mazda 626

1 Answer

Transmission is slipping in my 1986 mercedes 190E. Was told it was an easy fix with a 50$ part. Is this a common problem with this model?


Depends, it can be the stage pistons which is replaceable from the outside and is fairly cheap. It is worth trying, if it doesnt then if it needs a rebuild those parts are already replaced. He may have meant the modulator also. Same idea for it. Better 50 dollars than 1500-2200 for a replacement.

Mar 03, 2010 | 1986 Mercedes-Benz 190

2 Answers

Recomended weight of diesel oil mazda 2200


diesel engine oil is usaly 15w40

Sep 24, 2009 | 1988 Mazda B2200

1 Answer

Golf 1 clutch keeps slipping


Yes, replace it. It wears out just like brake rotors do. If it is too thin the clutch will slip.

May 27, 2009 | 1986 Volkswagen Golf

1 Answer

Transmission slipping making noise


If u keep it below 25 miles an hour you should make it, but this loud noise worries me, this noise means something is coming apart, if it does it may lock the trans up, so keep the speed down.

May 27, 2009 | 2003 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...