Question about Daewoo Lanos

Open Question

My daewoo lanos starts very well but when u rave it goes like bobobo no compresion, so what causes that and whats solution?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 90 Answers

SOURCE: daewoo problems

HI
is the service engine light com on when you turn the switch on ??
if no . check fuses ??
if yes . check the CKP crankshaft position sensor ??

give us more details to can help you pleas !!!
with my best wishes

Posted on Jul 15, 2008

Ad
  • 6 Answers

SOURCE: reset passcode for radio of 2002 daewoo ,lanos

MINE CAME ON A SMALL METAL TAG ON THE SPARE KEY

Posted on Jul 16, 2008

emissionwiz
  • 76691 Answers

SOURCE: diagnostic codes for 200 Daewoo Lanos..........

Do you feel a misfire?? Random misfires are usually caused by a lean fuel mixture, the reasons that cause this a to many to list here.

Posted on Jul 30, 2008

Ray190te
  • 61 Answers

SOURCE: Which Oil do I put in 1997 Daewoo Lanos?

For the engine any regular 10w30 engine oil will be ok

Posted on Jan 19, 2009

stevenhurc
  • 450 Answers

SOURCE: 2001 Daewoo Lanos Fault 63.58X 'B'

DTC 63 Will Set When
No voltage is supplied by the ECM through the EST “B” line while reference pulses are received by the ECM from the crankshaft position sensor
check white wire terminal B on ignition coil to ECM terminal C14 for open circuit or short to ground while disconnected if thats ok check for voltage signal at B while cranking no signal ECU faulty. voltage signal also on A terminal while cranking and check earth terminal C to body no higher than 5 Ohms
power is terminal D 12V
if getting power, earths good, and both signal voltages are going into coil pack, coil pack is faulty.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Should i take the cylinder heard for repair or whats the solution to compresion of daewoo lanos?


depends on the cause.
blown head gasket

warped cylinder head - re-machine of head required

Cracked head - head needs welding and machining

Dec 04, 2016 | Daewoo Cars & Trucks

1 Answer

If a waterpump siezed on a Daewoo Lanos would that break the camb


Yes. I think. A lot of cars have the water pump under the timing cover and you change the pump when you change the timing belt. They usually don't seize though, they just leak. Did you run it after it broke? How long before the engine quit? Did it start knocking? When you go to change the belt, look for a broken cam, or other damage that the broken belt would have caused. Some engines are free running, meaning they will turn over no problem when the belt goes, other engines are intermittent, meaning the valves hit the tops of the pistons and cause considerable damage. Find out before you go too far. Hope this helps.

Apr 02, 2010 | 2002 Daewoo Lanos

1 Answer

2000 Daewoo Lanos 'jumps' when pulling away and in low gears.


Ignition Coil, or Crankshaft sensor going bad. Change your spark plugs and wires then see what happens. Or could be your injectors are clogged. Try some pour in the tank Fuel Injector Cleaner like STP. Any little debris can mess them up.

Oct 31, 2009 | 2000 Daewoo Lanos

1 Answer

I have a daewoo lanos 1349cc se i have put new piston rings had the valves re-cut and re-ground fitted new valve stem seals new hydraulic tappets replaced oil pump also had cylinder head skimmed and fitted...


Check your key immobilizer, i had a similar problem with my Lanos.
If you turn the key and your red light keeps flashing in the centre console your imobilizer is not turning off.

Oct 29, 2009 | 2001 Daewoo Lanos

1 Answer

Daewoo lanos 2000the car will not start dies out when gas applied


possible blocked fuel filter or fuel pump not supplying enough fuel (starving) check fuel pressure with pressure gauge
also blocked exhaust or cataletic convertor can cause same issue

Jun 26, 2009 | 2000 Daewoo Lanos

1 Answer

Car is over heating. water starts to boil


Hi
The thermostat could be stuck closed. It also could be the cooling fan motor
is burnt out causing fuse to burn out.

Apr 02, 2009 | 1999 Daewoo Lanos

4 Answers

Diagnostic codes for 200 Daewoo Lanos..........


Do you feel a misfire?? Random misfires are usually caused by a lean fuel mixture, the reasons that cause this a to many to list here.

Jul 23, 2008 | 2002 Daewoo Lanos

1 Answer

Help


HAD THE SAME PROBLEM WHICH WAS CAUSED BY CLOGGED VALVE LIFTERS! DRAIN EVERYTHING AND START AGAIN

Jun 17, 2008 | 2002 Daewoo Lanos

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...