Question about Cars & Trucks

Open Question

My prostart remote fob has gone into sleep mode. How do I get it to turn on again?

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 645 Answers

SOURCE: prostart remote starter is in sleep mode. How to get out of sleep mode

To get an iBook out of sleep mode, you can hit any button on the computer. ----------------------------------------------------------------------------
Car Key Programmer

Posted on Nov 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced the battery in the fob and disconnected and re connected the battery, car still does nothing. It's like it has gone to sleep? Remote locks won't work, car won't respond. HELP


get some advice from an alarm installer/parts suppler with experience of your alarms make. It may be something fell out of the fob, a chip/ is the battery in correctly positioned.does a break in the pcb in the key fob lose settings so the fob is no longer recognised. You probably need the assistance of somebody experienced in the servicing of your alarm
Alternatively provide details of make and model and resybmit the query

Jun 06, 2015 | Cars & Trucks

1 Answer

I have prostart 3 way new installed into 1995 f250diesel can't get remotes to conect to the prostart brain box


Verify batteries are installed and installed correctly in the remotes. Examine the batteries and the battery holders on the remotes for "shipping isolators", pieces of plastic film or tape that insulate the batteries from the battery contact points. Verify the batteries are fully charged with a volt meter. Beyond these basic check points, contact prostart support.

Jan 19, 2014 | Cars & Trucks

1 Answer

How do I reprogram Prostart remote starter/car alarm after replacing car battery?


Try turning the Prostart off, then on with the little toggle switch. Check that the hood pin switch is working as it should

Dec 03, 2013 | Cars & Trucks

1 Answer

Prostart remote starter is in sleep mode. How to get out of sleep mode


To get an iBook out of sleep mode, you can hit any button on the computer. ----------------------------------------------------------------------------
Car Key Programmer

Nov 22, 2012 | Cars & Trucks

1 Answer

Remote control has stopped working. Have tried changing the battery of the remote control but that did not work.


Does the red light on the remote light up when you push any of the button
if no, replace remote
if yes, then try repograming the remote to the car again.
-Have remotes' ready. if you have two then fob#1 and fob#2 (doesn't matter which one is #1 or #2)
-each step has to be done within 5 sec or it will not work, but don't do it super fast.
1.turn key just to the "on" position (not starting) and push "lock button " on fob#1 once and release
2.turn key off
3.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
4.turn key off
5.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
6turn key off
7.turn key just to the "on" position (not starting) and push "lock button " on fob#1 twice (if you only have one fob, then stop here and go to step 8)and push the "lock button" on fob#2 twice.
8.turn key off and remove key from ignition.
if you did it right, remotes' should work again.
good luck

Dec 17, 2010 | 2003 Honda Accord

2 Answers

Both key fobs for honda pilot 2006 no longer works. Do I need new keys or is it something internal such as a fuse?


First thing, does the red light on the remote light up when you push any of the button
if no, then replace battery inside remote
if yes, then try repograming the remote to the car again.
-Have both remote ready. fob#1 and fob#2 (doesn't matter which one is #1 or #2)
-each step has to be done within 5 sec or it will not work, but don't do it super fast.
1.turn key just to the "on" position (not starting) and push "lock button " on fob#1 once and release
2.turn key off
3.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
4.turn key off
5.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
6turn key off
7.turn key just to the "on" position (not starting) and push "lock button " on fob#1 twice (if you only have one fob, then stop here and go to step 7)and push the "lock button" on fob#2 twice.
8.turn key off and remove key from ignition.
if you did it right, remotes should work again.
good luck

Dec 17, 2010 | Honda Pilot Cars & Trucks

1 Answer

Got a 2003 mercury grand marquis which i bought and didnt come with a remote for the door locks. i have an extra remote from my 2003 ford expedition and need to know how to program it, any suggestions?


usually the truck and car fobs work on different signals. you can get inexpensive fobs on ebay, the car fob will have four buttons with a trunk release button.
once you have the correct fob, its pretty easy.
  • Just remember that you must also re-program your currently working remotes at this time also as if they are new since prior remotes are erased.
  • Max of 4 transmitters can be programmed.
Procedure:
  • Keep the driver's door open.
  • Electronically unlock the doors (Switch on door or working transmitter)
  • 2000-2006: Turn the ignition from OFF to RUN/ON 8 times within 10 seconds, with the eighth turn ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.
  • Within 20 seconds, press any button on an transmitter, and the doors will lock and then unlock to confirm that each transmitter has been programmed. Repeat this step for each transmitter.
  • NOTE: If the door locks do not respond for any transmitter, wait several seconds and press the button again.
  • To exit the programming mode:
    • Turn ignition to the OFF position.
    • Let the 20 seconds expire.
    • The maximum number of transmitters have been programmed.

Sep 04, 2010 | 2003 Mercury Grand Marquis

1 Answer

How to program a keyless entry fob for 2005 gmc envoy - i am replacing the battery in my key fob every 5 days. I have to be right next to the car for it to work. Any idea what would cause this. I ordered a...


Seating in the drivers seat , make sure all doors are closed.Insert key into ignition, don't turn on yet.
Wait for the dome light to go out, then press and hold the door unlock button , make sure it is UNLOCK, while turning the key ON OFF ON OFF Twice , do not engage the started, just on to the point of being on. Release the unlock button,and your doors should lock, then unlock indicating programming mode.At this point hold down both the lock and unlock button on the key fob. After 30 seconds your locks should lock and unlock, indicating the fob is programmed. This must be repeated for all remotes, whether or not it be new or old. After all remotes are programmed, turn the key off and on again to exit programming mode.

May 18, 2009 | 2005 GMC Envoy

1 Answer

Programming instructions for a 1999 Chrysler 300M remote fob


Manual Programming Procedure (non scan tool)
1. Connect pin 1 of the 16-way data link connector to chassis ground or to pin 4 of the 16-way data link connector.
2. Close all doors, turn ignition key to off.
3. Turn ignition key to Accessory.
4. Turn ignition to off, door locks will cycle once (in programming mode).
5. For each key FOB, press any button 3 times in a row to program code. When programming is complete, the door locks will cycle once.

NOTE:
IF A SECOND KEY FOB REQUIRES PROGRAMMING, IT MUST BE PROGRAMMED WITHIN 1 MINUTE OF PROGRAMMING
THE FIRST FOB PROGRAMMING. PRESS ANY BUTTON ON THE SECOND FOB 3 TIMES TO PROGRAM ITS CODE. WHEN PROGRAMMING IS COMPLETE, THE DOOR LOCKS WILL CYCLE ONCE.

6. The programming mode finishes after the following:
a. Programming of two key FOBS is completed.
b. One minute has passed since programming.
c. Pin 1 of 16-way data link connector is removed from ground connection.
d. Ignition switch is turned on.
e. Any of the doors are opened.

Apr 09, 2009 | 1999 Chrysler 300M

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...