Question about 2010 Cadillac CTS

Open Question

I just my 2010 cadillac cts breaks fixed but all my break lights r on how do i reset them

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bigg t
  • 640 Answers

SOURCE: break / hazard light fuses keep blowing

check both brake lights for moisture getting into them.

Posted on May 26, 2008

1MINTZ
  • 14 Answers

SOURCE: how to reset low fuel

when refueled the light should reset. Turn on ign on the "on" position pump acell pedal 7-10 times. Turn ign off then on and start the vehicle, This might help

Posted on Sep 17, 2008

yotaguy
  • 232 Answers

SOURCE: reset change break pads light

With a code scanner or I do beleive it will clear after 100 starts.

Posted on Jun 02, 2009

morse008
  • 1111 Answers

SOURCE: HOW TO REPLACE A BREAK LIGHT SWITCH

The brake light switch itself is located on the brake pedal follow it down until you see where it connects and unplug the connection ...after installation make sure the brake light switch is correctly adjusted by having a 2nd person stand behind the vehicle as you press the pedal the light should come on if not adjust the switch higher up by turning the switch inward ..or upwards by screwing it in if it constantly on unscrew it until lights go out and its fairly easy once you actually look at the part and the pedal ...i hope that helps you

Posted on Nov 13, 2009

  • 1 Answer

SOURCE: 2006 cadillac CTS Wheel hub replaced , now

if you hold F1 and F6 in on your radio it will give you the option to erase all codes

Posted on Dec 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing battery in a 2010 Cadillac CTS 3.6 awd


Replacing battery in a 2010 Cadillac CTS 3.6 awd ? You don't know where it is or you don't know how to replace a battery ?

Dec 01, 2016 | 2010 Cadillac CTS

1 Answer

Problems with Cadillac CTS 2003 abs light on and break light and traction light there on


Could be as simple as a wheel sensor... Run up to autozone and plug up and run the codes...

Sep 03, 2016 | 2003 Cadillac CTS

3 Answers

How do I reset computer on 2005 Cadillac cts


Disconnect the negative cable from the battery, then go inside your car and press the break pedal for 30 seconds. That should drain the extra power and reset your computer.

Jan 23, 2015 | 2005 Cadillac CTS

1 Answer

Removing an alternator from 2004 cadillac cts


buy a service manual , dont break the heater bypass valve either

Mar 30, 2013 | 2004 Cadillac CTS

1 Answer

How to remove front seat back 2010 cts


Remove the front and rear trim covers over the four bolts that hold the seat to the floor, then go under the seat and disconnect all the wiring being careful not to break any of the connector locking tables.

Jul 12, 2012 | 2010 Cadillac CTS

1 Answer

My cadillac cts 04 the break lights wont turn off. i already changed the break light switch im thinking its the fuse. wats the name of this fuse and were do i find it? any help is good thank you


Hello. Under your brake pedal is a switch with a plunger on, that activates your lights when depressed. Just follow up along the pedal and you will see (probably) a white switch. It sounds like the plunger switch is stuck in. These are quite cheap to replace and you might be able to prise the plunger switch out to turn the brake lights off. If it was a fuse it would not work. Can you leave feedback if this helps. Thanks

May 28, 2011 | 2004 Cadillac CTS

1 Answer

How do you remove and replace the ignition lock housing on a 2003 cadillac cts


it would be cheaper, if you lost your key ,to take your vin to cadillac dealer and proof you own it to have them make a key.if you change the cylinder lock youll have to reprogram the antitheft system and possibly breaking the sensor changing the lock and that get pretty pricey. you can get a key made cheap ready to go.cadillacs antithefts are very touchy systems.

Jul 13, 2010 | 2003 Cadillac CTS

1 Answer

How do I replace the drivers side rear break light


Open trunk unscrew black knobs that hold trunk panels down. Remove panels look in the trunk on the oppisite side of the taillight unscrew the two nuts pop off the taillight replace the burnt out break light .Put everything back on the same way you took it apart.

Jan 02, 2010 | 2005 Cadillac CTS

Not finding what you are looking for?
2010 Cadillac CTS Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...