Question about Cars & Trucks

1 Answer

'its been slightly altered' - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 2,494 Answers

What has been altered.

Posted on Dec 03, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1983 280 ZX turbo, there is a slight hesitation when accelerating. What can cause this?


if this is a carby engine then the hesitation can be from a faulty power valve in the carby (Carby overhaul) or incorrect timing . It could be an indication that the turbo is not spooling up quickly enough to produce the air required on acceleration Check for any split/loose vacuum hoses that are altering the mixture

Jul 16, 2014 | 1983 Nissan 280ZX

1 Answer

Ok 1992 50 hp force magnets fell out of the fly wheel put a new fly wheel on do i have to reset the timing .


IF the magnets are fixed in position with not allowance for adjustment then the timing should be the same as before. The problem may be that if they have hit on the coil as they come out then it may have moved and that will alter slightly the timing point . Basically I would expect it to start as before.

May 21, 2014 | Cars & Trucks

1 Answer

Wat will happen if my coolant light came on and all i had was regular anti freeze,the 50/50 and i put some in my 2002 745li bmw


If you are only adding a couple of litres, the freezing point of the coolant will be altered very slightly. The important thing to check is that the antifreeze you are adding is suitable for alloy engines. If you add water the freezing point of the coolant will be raised, again very slightly if you only add a couple of litres

Apr 03, 2013 | Cars & Trucks

1 Answer

Front porch censor


Light sensors have 2 adjuster screws on them that you can set for you particular situation. One alters the distance that the sensor reacts to and switches on and the other is the sensitivity of the sensor so that slightly moving or slow moving items will not set them off . The bulb you are using will also alter the operation so stick with and incandesant bulb rather than a energy saver.

Mar 10, 2013 | Cars & Trucks

2 Answers

How do I stop rattly tappet noise?


Rick you don't say what vehicle it is. I don't believe mixing oils will affect tappet noise unless one of the two oils was way too thin a grade.

If all else is OK, rattly tappets aren't generally a big worry unless you also get hard starting, which indicates the valve timing is way off. I've had vehicles in which valve noise was factory standard LOL.

You could try an oil change with one grade heavier.

The rattle might also indicate that the upper cylinder head is being starved of oil, either due to low pressure, or sludging. You could get oil pressure measured to eliminate that possibility.

After all else if you want to go further you could get the valve lash adjusted, but in some motors it is a helluva job, and in a van, it is more difficult.

Aug 27, 2017 | Cars & Trucks

1 Answer

Trying to ****** the ignition but the distributor doesnt move when loosened is there some kind of other adjustment?


Your distributor is "locked". Timing is regulated by the computer using the crank sensor, throttle position sensor, cam sensor and MAP sensor as its primary references. Pretty much the only way it mechanically can become inaccurate is for the timing chain to stretch, or for someone to remove the distributor to have been removed and installed a tooth off.
Generally the factory setting is all you need but in extreme cases or if attempting to gain a small performance gain, the bolt hole in the distributor lock can be slightly enlarged to allow a degree or two of additional lead to be dialed in. You can also find a diagram to alter the MAP sensor online to alter it further.

Oct 28, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Low growling noise in front end


typically, this sounds like a wheel bearing. To test, the noise can often be altered by accellerating /decelerating, and more evident by turning the vehicle.

The truning process is to put load on one side, then the other. if the right side has a damaged bearing, for example, the noise would be noticibly altered (less in this case) when turning to the right. Load would be slightly less. Testing speed in the area of 25 to 35 mph.

doc

Sep 14, 2009 | 2003 Nissan Altima

1 Answer

Have a 96 camry, the keyway groove on the crank for timing gear is larger than the key. the gear is fine, I believe this caused a rattle sound. Thats why i tore it down again. I did not notice this the...


Replacing the crankshaft for such a minor thing should not be an option, Find a key that fits the wider groove and file the outer portion to fit the gear. Tedious, but far cheaper! Align the filing effort or you will alter the timing slightly.

Aug 17, 2009 | 1996 Toyota Camry

1 Answer

Enter the code


have a look in the radio book as every model of car is different,normally the first four numbers on the preselect are the operating controls for the code ,1 button is then altered by using the volume vontrol or tuning control for higher or lower numbers then no 6 button locks it in ,but a they are all slightly different so have a play

Feb 26, 2009 | 1997 Mitsubishi Galant

1 Answer

IAT sensor wires


Those chips are not chips just a 5 cent resistor to alter the IAT (Intake Air Temperature) signal to the PCM (Powertrain Control Module), the idea is that the engine control computer thinks it is getting colder air than it really is and slightly increases spark advance, u will feel no difference in power but u may gain 1 MPG in fuel economy, so u decide. One last note they are illegal in most states that do emission tests, it alters the factory controls.

Oct 29, 2008 | 2007 Chevrolet Colorado (Extended Cab) New...

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...