Question about BMW Cars & Trucks

Open Question

Hi I need the talk settings for my freelander engine It's a freelander 1td4 2l BMW motor crank shaft , condrod And head please

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: 1992 BMW Cylinder head

30nm 90 degrees, 90 degrees Renew bolts!!

Posted on Jun 20, 2008

  • 10 Answers

SOURCE: Can not find filter

Hay..It's easy to find....It's in the rear left hand Conner under the engine compartment..Always replace it in to the order..because sometimes td4 will not rev above 2000rpm if the fuel filter got blocks...

Posted on May 07, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

  • 1 Answer

SOURCE: toyota tarago 2az fe motor

Rustam.Where is the fuse for radio of 2003 toyota tarago

Posted on Jan 24, 2010

  • 1 Answer

SOURCE: freelander td4 wont start

I have exactly the same issue!

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the timing marks for a 2004 bmw x5 3.0 liter engine?


The timing marks for the cam chain are just basic set up. You will need factory special tools to lock crank and other shafts in place to do this correctly.

Jun 30, 2015 | BMW X5 Series Cars & Trucks

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

I have 1993 bmw 740il I try to replace the


Hi, you must take off the crank shaft pully to access the water pump use # 13 mm socket or Torx socket (not sure wich one) to take off the crank shaft pulley bolts.
Good Luck!!

Jan 10, 2010 | 2006 BMW 750Li

2 Answers

Hyundai elantra 1.6GLS J2 torque settings


dear friend:here follows the settings in need:
cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
mains-30nm +65deg
big ends- 1 - 26nm 2 - 52NM
fly-wheel -130nm
cam-sprocket - 100-120
crank-pulley - 170-180
cam caps -15nm

Aug 31, 2009 | 1995 Hyundai Elantra

5 Answers

Freelander td4 wont start


I have exactly the same issue!

Jun 07, 2009 | 2003 Land Rover Freelander

1 Answer

I have a 1993 bmw 325i and a need to change a crank position sensor and i just want to know How do you replace the crank sensor on a BMW?


Hi the crank shaft sensor is located just above the front pulley at the front of the engine and is held in place be a 5mm hex bolt, undo this and remove the sensor then you will need to follow the wire that dissapears under the intake manifold and unplug the multiplug, replacement is the reverse, regards mark

May 04, 2009 | BMW 325 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...