Question about Ford Cars & Trucks

1 Answer

Is there anotherloacation for a crank position sensor on a1997 Ford 5.8 LTr F 250 motor besides by the pulley near the AC compressor

Posted by on

  • Timothy Turner
    Timothy Turner Dec 03, 2016

    The whip and sensor isn't there

  • Jeff Armer Dec 10, 2016

    Passenger side of engine on timing cover

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 13,008 Answers

What year and model ? LTE ? your looking at the crankshaft harmonic blancer pully ?

Posted on Dec 03, 2016

Testimonial: "1997f250 5.8 ltr"

  • Timothy Turner
    Timothy Turner Dec 10, 2016

    Yes the crankshaft harmonic balancer pulley

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My truck won't start after putting a bypass pulley on it


probably damaged the crank position sensor while fitting the belt

Sep 24, 2016 | AC Cars & Trucks

1 Answer

Ford Expedition 2001 crankshaft sensor location and installation


  • Located front of engine, close to crank pulley
  • press the helpful button and follow me on Fixya for more tips
  • Insert the square tip of a 1/2-inch socket wrench into the square hole in the center of the serpentine belt's adjustment pulley. The adjustment pulley is the smallest pulley the belt wraps around.
  • Pull the adjustment pulley toward the engine with the socket wrench to release the tension on the serpentine belt, then pull the belt off the air conditioning compressor's pulley.
  • Remove the bolts which secure the air conditioning compressor to its mounting brackets with an open-end wrench, then position the compressor to the side of the engine compartment. Do not disturb the hoses that attach to the compressor.
  • Pull the electrical connection off the crankshaft sensor.
  • Remove the two bolts that secure the crankshaft sensor against the engine with an open-end wrench, then slide the sensor out of the engine.
  • Slide the new crankshaft sensor into the engine, then install and tighten the sensor's two securing bolts with an open-end wrench.
  • Press the electrical connection onto the crankshaft sensor.
  • Position the air conditioning compressor against its mounting brackets, then install and tighten the compressor's bolts with an open-end wrench.
  • Pull the serpentine belt's adjustment pulley toward the engine with the socket wrench, then position the belt onto the air compressor's pulley. write up found @ehow

How to Replace the Crankshaft Sensor in Ford 150 eHow

Jan 28, 2016 | Ford Expedition Cars & Trucks

1 Answer

New Crank shaft pulley was installed, then Mazda Tribute 2.3lL won't start


check for damage /wire connections to the crank shaft position sensor near the harmonic balancer pulley. Check the air gap of the sensor

Apr 15, 2014 | Mazda Tribute Cars & Trucks

1 Answer

How to replace 2003 lincoln town car crankshaft sensor


The crank position sensor on this car is near crankshaft pulley and you have to take acces drive belt off and loosen the ac compressor in order to have room to wiggle it out. Will not clear the ac compressor unless you do this.

Feb 12, 2012 | Renault 181 Cars & Trucks

2 Answers

HOW DO YOU INSTALL A CRANK POSITION SENSOR 1999 CHEVY ASTRO VAN 4.3 LTR MOTOR


The crank sensor is inside the distributor and may also be called an HEI pickup.
Disconnect wiring harness and remove the two tork head screws and lift out. Now would be a good time to replace the rotor & distributor cap if you haven't done so lately.
I hope this helps.

Jul 07, 2011 | 1999 Chevrolet Astro

1 Answer

I need help finding crank shaft position sencor on a 1992 licoln town car


The Crank position sensor is located on the drivers side front of the engine below the AC compressor and picks up its signal from the front crankshaft pulley trigger ring. In the picture below is a technican grasping the connection to the sensor and the sensor directly in front of the connector.





emissionwiz_161.jpg

Apr 22, 2011 | Lincoln Town Car Cars & Trucks

1 Answer

Cannot find crank shaft position sensor on 2004 lincoln ls v8


Passenger side of crank pulley under ac compressor by pulley.

Jan 15, 2011 | 2004 Lincoln LS

1 Answer

No spark on a 1996 lincoln mark 8


Hi,

A no spark is due to a failed or malfunctioning Crank Position Sensor locacted by the crank pully, near the AC compressor.

Sometimes you can upplug the sensor and when you plug it back in the car will have spark again.
However,Replacing the sensor does require removal of the AC compressor (due to space limitations) BUT you do not have to disconnect the AC lines.
Simply unbolt the compressor and gently lay it aside, and that will give you the clearance to pull the Crank Sensor from the block.

Good luck!!!

Aug 09, 2010 | 1996 Lincoln Mark VIII

1 Answer

Where are the oxygon sensor location for 1999


They are located in the exhaust system near the front of the exhaust. A 7/8 wrench can be used to remove them.

Mar 15, 2010 | 2003 Ford E250

2 Answers

Need to bypass ac compressor on a1997 chevy lumina 3.1l


the models without AC use a AC delete pulley, so there is only one belt size, the pulley goes where the compressor is in your with AC car, contact Ford for the AC delete pulley

Apr 28, 2009 | 1998 Mercury Mystique

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...