Question about Toyota Cars & Trucks

1 Answer

I NEED TO SET TIMMING IN MY TOYATA TAZZ 1.3 2E ENGINE

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 7,515 Answers

Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Posted on Jan 04, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix a oil leak on a toyata tazz?


depends on whats leaking doesnt it?? unless you want to replace every gasket and seal......

Mar 05, 2018 | Cars & Trucks

1 Answer

How many intake valves does a toyota tazz 2e engine 2004 model have


earlier 2Es have one inlet one exhaust
after the east west front wheel drive were introduced
most 2E toyota engines have three valves per cyl
two inlets and one exhaust

if you need the correct information on your 2004 2e engine
,,,,undo the rocker cover

e397a648-22cf-4373-b847-0ca46d719837.jpg

Jun 28, 2016 | Toyota Cars & Trucks

1 Answer

I would like a workshop manual for a Toyota Tazz 1300 2001 model


I would suggest you try your local eBay for a used manual.

Jun 23, 2016 | 2001 Toyota Corolla Hatchback

1 Answer

Too heavy on fuel


there is no carb. in modern cars, unless...
2005 Toyota Tazz 130
what country are you in, cabs ended in 2006 in far from USA countries.
so that you? in S.Africa or some small Island in the Pacific running JDM cars?
quote, this you?
A facelifted version of the sixth-generation five-door hatchback was made in South Africa as an entry-level model called the Toyota Tazz from 1996 until July 5, 2006. The Tazz was offered as 130, and 160i. It was also sold as a panel van called the Carri. [4]
end quote.

why not post photo of engine.
or get the FSM on this car, factory service manual, at Toyota.
it covers all THAT.
if not a carb, you cant tune it, like a carb , you fix it.

my first idea> give it a tuneup, new spark plugs, filters.

Jan 23, 2014 | 2005 Toyota Tazz 130

1 Answer

How do I set the timming on a 1400 Nissan sentra 1998 model


This is for a 1998 nissan sentra 1.4 engine, start engine and allow to reach operating temp.then turn engine off and disconnect throtle postion sensor connector.

With tps sensor disconnected start engine and increase idle to 2000 rpm three times then release and allow it to idle.

now check timing, timing should be at 6-10 degrees BTDC. adjust as needed then turn key off and reconnect tps .
Good day.7_15_2012_4_06_52_pm.gif7_15_2012_4_07_06_pm.gif

Jul 15, 2012 | Nissan Sentra Cars & Trucks

1 Answer

Timing marks


you should have timming marks on the front engine block. if you see it you will need a timming light to set it very cheap to buy. if you do not see any timming marks and you have a distributer losen it a little but with the car running. now with the car running turn the distruber left or right until you hear and feel the car idle high. once you feel it idle low go back up until it idle high and keep it there and tighten the distruber back. turn the car off and try starting it back up. it should start right on time with the correct timming and idle. good luck

Jul 08, 2009 | 1995 Chevrolet Monte Carlo

1 Answer

2002 jeep liberty timming marks


you cant without proper computer tools

Jan 26, 2009 | 2002 Jeep Liberty

1 Answer

Need to set timing on 1990 chevy pu 5.7 engine "K" ?


set cylinder 1 to top dead center then set the distributer to the #1 wire contact, snug down the distributor and start the engine, then hit the crank dampener with a timming light while clipped to the #1 spark plug wire and turn the distributor till the timming light is showing 0 on the crank, then tighted it down and timming is set.

Dec 11, 2008 | 1990 GMC K2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...