Question about Renault Cars & Trucks

1 Answer

Renault clio2006 mk111 torque wrench setting rear brake hub drum nut Also do you have to fit a new nut

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 784 Answers

275 Newton meters, yes you should use new nut, but should be fine if nut is in good condition

Posted on Dec 03, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque setting for Renault clio mk111 2006 rear brake drum hub


175 Newton meters is torque you are supposed to use new nut, but in my experience using the old one is fine

Dec 03, 2016 | Renault Cars & Trucks

1 Answer

How do you remove a rear hub on a 04 kia sedona?


Call Kia with your VIN to make sure yours wasn't affected by the recall. You may be able to have that rear bearing replaced for free at Kia.

HUBCAP & OUTER BEARING REPLACEMENT PROCEDURE: 1. Remove the two (2) cross-tip locating screws on the brake drum.

2. Remove the brake drum.

3. Remove cotter pin and cover set.

4. Remove nut, claw washer, outer bearing and hub assembly.

5. Inspect inner bearing area in both hubs for any sign of moisture, corrosion, grease discoloration or contamination. If "yes" discard entire hub and replace with new assembly. If "no" proceed with outer bearing replacement below: 6. Carefully remove the outer bearing race from the hub. If the hub assembly is damaged then replace the hub assembly as a complete unit. (If inner seal is damaged while removing the outer race replace with new seal.)

7. Clean all contaminated grease from outer bearing cavity of the hub.

8. Install a new outer race into the hub using an appropriate race installation tool.

9. Apply grease MS511-33 WBG2 or equivalent to the hub assembly and the new bearing(s) especially to the shaded areas.

10. Install hub assembly, new pre-greased outer bearing and new claw washer on spindle. (Or alternatively, install entire new hub assembly, as supplied). Ensure bearings are properly seated then tighten hub/spindle nut, torque nut to 20-25 lb-ft (27-33 Nm.) Verify hub spins freely without signs of binding or excessive play.

11. Install new cover set and cotter pin; never reuse the old cotter pin.

12. Install new hub cap with Loctite # 5910(TM) or equivalent sealant to prevent moisture intrusion.

13. Install the rear brake drum using tapered locating screws.

14. Install rear wheels and torque lug nuts to proper specification. (65-79 lb-ft) (88-108 Nm, 9-11 kgm)

15. Lower vehicle.

Dec 30, 2014 | Cars & Trucks

1 Answer

Torque setting for wheel nuts on Renault Alloy wheels


130(NM) 96 ft/lbs is the torque setting for a 2008 renault scenic so as not to ruin studs or brake rotors should be sufficient for allloys just need to check alloy lug nuts more often

Aug 09, 2014 | Renault SCENIC Cars & Trucks

1 Answer

How to change a rear wheel bearing on a 2004 ford taurus???


How to Replace Rear Wheel Bearing/Hub Assembly on a 2nd generation Taurus

The following procedure is for a Ford Taurus (VIN S), with rear drum brakes and ABS.

1. Loosen wheel lug nuts, raise rear of vehicle, and support securely on jack stands. Block front wheels and remove rear wheels.

2. Remove brake drum (parking brake must be off).

3. Remove and clean ABS Sensor (Torx E8) with a spritzled rag.

4. Remove grease cap from hub.

5. Remove and discard hub retaining nut (36 mm). This is a compound nut, comprised of several nuts inside a metal cage. Use a 36 mm axle nut socket (e.g., OEM 25206). Many auto parts stores will lend you this socket. A 1/2-inch drive air impact wrench or breaker bar is necessary to remove the nut.

6. Remove wheel bearing/hub assembly from spindle. It easily comes off by hand.

7. Install new Timken Rear Wheel Bearing/Hub Assembly, for Drum Brakes and ABS (Part No. 512162). Tighten new axle spindle nut (Dorman 05114) 221 lb.-ft., replace grease cap, and button everything up.

Jun 22, 2012 | 2004 Ford Taurus

1 Answer

How do I get the rear drums off a 2000 Ford focus. I removed the spindle nut,


2000 Ford Focus Drum Removal ProcedureIf removing the drum to service the rear brakes: (note, do not remove hub retaining nut for this procedure)
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Disconnect wheel speed sensor wiring harness from wheel knuckle and floor panel.
5. Remove 4 wheel spindle attaching bolts, then the wheel hub and drum assembly from vehicle.
6. Reverse procedure to install noting the following:
a. Torque wheel spindle retaining nut to 49 ft. lbs.
b. Torque wheel/tire assembly to 94 ft. lbs.
2000 Ford Focus Drum Replacement ProcedureIf replacing the drum and wheel bearing assembly:
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Remove center dust cap.
5. Remove hub retaining nut.
6. Remove drum and hub assembly. Ensure wheel speed sensor ring is not damaged when removing drum/hub (if equipped).
7. Reverse procedure to install noting the following:
a. Inspect and clean wheel speed sensor ring if equipped.
b. When tightening hub retaining nut, rotate the hub assembly in counterclockwise direction.
c. Torque hub retaining nut to 173 ft. lbs.
d. Torque wheel/tire assembly to 94 ft. lbs.
e. Adjust parking brakes as necessary.


Jul 05, 2011 | 2000 Ford Focus

1 Answer

Where the hell can I get a FREE PDF download for my Ford fusion 2 for the removal and replacement of the rear wheel bearings as well as the torque settings for the final nut after replacement.All the so...


Rear Suspension - Rear Wheel Bearing Fusion 2002.75 (06/2002-)

-Removal and Installation

Special Tool(s)

Installer, Differential Bearing
205-062

Installer, Input Shaft Seal
307-210 (17-041)


General Equipment
Soft faced hammerWooden block

Removal

CAUTION: The brake drum and hub assembly removal in this procedure is for installing a new wheel bearing, not for access to brake system components.

-All vehicles

Remove the dust cap.
Remove the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

-Vehicles with rear drum brakes
Release the parking brake.
Remove the brake drum and hub assembly.
Remove and discard the wheel hub retaining nut.


-Vehicles with rear disc brakes
Remove the brake disc.
For additional information, refer to in this section.

Remove the wheel hub.
Remove and discard the wheel hub retaining nut.


-All vehicles

Remove and discard the wheel speed sensor ring (brake disc shown).
Remove the circlip (brake disc shown).
Using the special tool, remove and discard the wheel bearing (brake disc shown).

-Installation

-All vehicles

CAUTION: Support the wheel hub assembly on the wheel mounting face and not on the wheel nut studs.

Using the special tool, install the new wheel bearing (brake disc shown).

Install the circlip (brake disc shown).

CAUTIONS:

Make sure the wheel speed sensor ring is not knocked, damaged and kept free from metal fragments.

Protect the face of the wheel speed sensor ring with a non-ferrous flat block to prevent damage.

Make sure the wheel hub or brake drum is adequately supported and do not allow it to rest on the wheel studs..

Make sure the wheel speed sensor ring is pressed on slowly and squarely until fully seated.

Do not exceed a maximum load of 10 kN.

Using the special tool, install a new wheel speed sensor ring (brake disc shown).

Vehicles with rear drum brakes

CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the brake drum and hub assembly.
Apply the parking brake.

-Vehicles with rear disc brakes


CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the wheel hub retaining nut.
Install the brake disc.
For additional information, refer to in this section.


-All vehicles
Install the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

NOTE: If the dust cap is damaged a new dust cap must be installed.

Using a soft faced hammer and a wooden block, install the dust cap.


There is no real torque settings for the rear wheels, except to say, do not over tighten or you will stretch the lugs and the will loosen over time.

May 28, 2011 | Ford Fusion Cars & Trucks

2 Answers

Torque on the rear spindle nut of a 1992 mercury cuogar


there is no torque you turn the nut till its thigh than back it off 1/4 turn put the cotterpin in and then the cap

Apr 24, 2011 | 1992 Mercury Cougar

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

Loose rear wheel, believe it is the bearing. How do I repair it?


drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

May 30, 2009 | 1999 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

xxxxxx xxx

Level 3 Expert

4836 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...