Question about Cars & Trucks

1 Answer

What is the cylinder head bolts torque setting for 13 vw polo 1.4 CCG engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,164 Answers
Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: need to know cylinder head bolt torque specs

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

  • 8 Answers

SOURCE: need cylinder head bolts torque settings for nissan 3.2d

what nissan model do you need the head torques for

Posted on May 01, 2009

  • 119 Answers

SOURCE: MISFIRING ON CYLINDER 1 VW POLO 1.4 3CYLINDER

I have changed a few cylinder heads under warranty for this type of problem. The exhaust valve guides wear, this causes the exhaust valve to seat badly, giving low compression. if one cylinder compresion reading is more than about 50 psi below the others, then this warrants head removal. It is quite a job, due to the fact that the camshft id chain driven. If you are up for it then once the head is removed, poor liquid into the exhaust ports and see if it leaks out through any of the exhaust valves.

Posted on Jul 23, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque settings for polo bah motor big ends :mains and cylinder head


CHECK BELOW..
25458898-ms2db0pp00uj21y1nio4xcxs-1-0.png

Tightening torques
Bolted connections Tightening torque
Bolts, nuts M 6 10 Nm
M 8 20 Nm
M 10 45 Nm
M 12 60 Nm
Deviating from above
Exhaust pipe to manifold 40 Nm
Installation
Note
t Only remove the new cylinder head gasket from its packing immediately before installing.
t Handle the new gasket with extreme care. Damaging will lead to leaks.
- Place a clean cloth in cylinders so that no dirt or emery cloth particles can get in between cylinder wall and piston.
- Also prevent dirt and emery cloth particles from getting into the coolant.
- Carefully clean cylinder head and cylinder block sealing surfaces. Thereby ensuring that no scoring or scratches are formed (when using abrasive paper the grade must not be less than 100).
- Carefully remove metal particles, emery remains and cloths.
- Set No. 1 cylinder piston to TDC and then turn crankshaft back slightly.
- To centralize, screw guide pins from 3450/1 into front outer holes for cylinder head bolts-flechas-.
- Place the new cylinder head gasket in the centralizing pins -A-. Lettering (Part No.) must be readable.
- Fit cylinder head, screw in 8 remaining cylinder head bolts and tighten by hand.
- Remove the guide pins with tool 3450 by the bolt holes. To do this, turn the tool left until the pins are removed.
- Fit remaining cylinder head bolts and tighten hand-tight.
- Tighten cylinder head in tightening sequence as follows:
- Tighten all bolts to 30 Nm.
- Then tighten all bolts a 1//4 turn (90 °) further using a rigid wrench.
- Then tighten all bolts again a 1/4 turn (90 °) further.
Note
There is no requirement to retighten the cylinder head bolts after repairs.
The rest of the assembly is basically a reverse of the dismantling sequence.
Note
When the camshaft is turned, the crankshaft must not be at TDC. Danger of damage to valves or piston crowns.
Installing toothed belt and adjusting valve timing > Chapter.
Filling with new coolant > Chapter.
- Interrogate fault memory > Chapter.

Feb 21, 2015 | 2006 Volkswagen Polo 1.6

3 Answers

Need to know the head bolts torch specs on 98 toyota v6


heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbsaf151d2.gif

May 12, 2010 | 1998 Toyota Sienna

1 Answer

Head bolt tourqe settings on a toyota cressida


Cylinder head bolt removal sequence


Removal sequence: Front 3 7 11 13 10 6 2 1 5 9 14 12 8 4

***CAUTION*** The above sequence must be followed during removal as to avoid warpage of the cylinder head unit

Reverse sequence to install, Step 1: Torque to 10 Ft/Lbs Step 2: Torque to 18 Ft/Lbs Step 3: Torque to 25 Ft/Lbs Step 4: Turn an additional 90 degrees Step 5: Turn an additional 90 degrees Step 6: Torque the 2 recessed 8mm bolts to 13 Ft/Lbs *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper Torque

Don't forget to rate this answer, Good Luck

Apr 24, 2010 | 1992 Toyota Cressida

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...