Question about Mitsubishi Cars & Trucks

1 Answer

How to replace coil and spark plug mitsubishi 1994 v6

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 76,846 Answers

The coils are bolted to the upper intake manifold, the spark plugs are at the other end of the wires from the coils.

Posted on Dec 02, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: MITSUBISHI GALANT

may be it is the engine that good condition...

Posted on Jul 14, 2008

  • 1 Answer

SOURCE: 1994 Grand Cherokee will turnover but no spark

i had the same problem, and it was the coil

Posted on May 02, 2009

SOURCE: 1994 Chevy S 10 Blazer-no spark, new coil

Did you try the distributor? It could also be the ignitor chip.

Posted on Jun 19, 2009

AutoDoc
  • 169 Answers

SOURCE: how can you test the spark plug coils, what is the

Dear Pablo,
You can check the input voltage at each coil. This way you make sure you have the proper amount to operate. Disconnect the six ignition coil connections. Turn the ignition key on. Check the voltage at Cyl #1 B/Y wire, Cyl#2 B/U wire,Cyl #3 B/O, Cyl#4 B/G, Cyl#5 B/R, Cyl#6 B/W and ground. It should be 10.5V or higher. If not,you need to find the cause of the voltage drop.
If ok, you can test the resistance of each coil. At the coil,measure the resistance across the primary windings.It should measure between 0.50 Ohms ans 1.00 Ohms.
I hope this information is helpful.If you need anything else,don't hesitate to ask. Thanks,Chuck.

Posted on Jan 02, 2010

Testimonial: "This is a great service you guys provide, keep up the good work. Thanks pablo "

  • 181 Answers

SOURCE: My 1994 Mitsubishi Lancer (4g15) engine stops

Fuel pump

Posted on Mar 06, 2010

Testimonial: "It's the fuel pump indeed. Also the gas tank found to be very dirty. The fuel pump was replaced, fuel system cleaned, now the car runs perfectly."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace ingnition coil and s park plug mitsubishi montero v6 1994


Coils normally screwed down. Remove screws and pull upward. This will give you access to plugs.

Dec 02, 2016 | Mitsubishi Cars & Trucks

1 Answer

Where can I find the spark plug wiring diagram for 1994 Camaro, v6 3.4 liter?


Engine Coil Pack
5 6 / #4 / / #3 / / #5 /
3 4 / #1 / / #6 / / #2 /
1 2
Front Ignition Wires on Coils
#1 #4 #6 #3 #2 #5
' ' ' ' ' '
O O O O O O

Firing Order: 1-2-3-4-5-6

Feb 24, 2015 | 1994 Chevrolet Camaro

1 Answer

Why1999 buick v6 3800 no spark from coil on one cylinder


OK, SO IF WIRES AND PLUG IS NEW, BE POSITIVE YOU HAVE NO SPARK remove wire from plug and hold near a screwdriver and you will see the baby lightning- do it when car is off and then start car and check for spark- don't fry yourself- more than enough current to kill if your a fool GET IT READY WHEN CAR OFF AND THEN START CAR AND SEE SPARK-- SAFEST WAY
IF THERE IS NO SPARK- THEN IT IS EITHER THE COIL ITSELF OR THE IGNITION MODULE THAT THE COIL IS ATTACHED TO -- GOOD LUCK AND BE SAFE PLEASE

Jun 19, 2014 | 1994 Buick LeSabre

1 Answer

1994 buick century coil pack location


The three coil packs are on the top of the engine, (I assume this is the 3.1 V6?) here is a picture of the coil pack, but all you need to do is follow the spark plug wires back to the coil packs (there are 3 on the V6).


1_23_2012_8_53_13_pm.jpg

Jan 23, 2012 | 1994 Buick Century

1 Answer

3 and 6 ignition coil do not fire


The module or computer might be bad.

Jul 05, 2010 | 1994 Mitsubishi Galant

2 Answers

1994 1.8 CC lancer has no spark Primary and secondary coils checked out ok Transistor checked out ok has power to coils when key is on Should spark????


So you're getting voltage to positive side of coils, but no spark at plugs? If you were to take the coil plug wire and hold it about 1/4 inch from engine ground do you get spark? (Use well insulated handles, don't touch metal) If yes, maybe plug wires, if no, does it have a control module? I'm not familiar with Mitsubishi, I've worked mostly on American cars.

Jul 05, 2009 | Mitsubishi Lancer Cars & Trucks

2 Answers

MITSUBISHI GALANT


may be it is the engine that good condition...

Jul 14, 2008 | 1994 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...