Question about Oldsmobile Cars & Trucks

1 Answer

Removing a right front fender on a 1998 oldsmobile regency.what bolts and retainers need to be removed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 1,335 Answers

Google your question or try youtube. Might also want to go to
1aauto.com

Posted on Dec 02, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the horn location under hood of a 2007 mercury mountneer?


Remove the LH front fender splash shield !
Fender Splash Shield Removal and Installation
  1. Loosen the running board bolts and lower the running board to access the front fender moulding pin-type retainer.
    • To install, tighten to 23 Nm (17 lb-ft).
  1. Remove the lower pin-type retainer from the front fender moulding.
  1. Remove the 2 rear pin-type retainers from the front fender moulding.
  1. Position the front fender moulding aside and remove the splash shield lower screw.
    >
  1. Remove the front splash shield screws.
  1. Remove the front splash shield pin-type retainers.
  1. Remove the front splash shield.
  1. Remove the front fender splash shield.
  1. To install, reverse the removal procedure.

Mar 25, 2015 | 2007 Mercury Mountaineer

1 Answer

How change front fender f150 2000


Fender -Front Removal
  1. Remove the radiator grille opening panel reinforcement (8A284).
  1. If equipped, remove the front wheel opening moulding.
    1. Remove the pin-type retainer.
    1. Remove the screws.
    1. Remove the wheel opening moulding.
    sy1~us~en~file=n12124a.gif~gen~ref.gif
  1. Remove the front fender splash shield (16103).
    1. Remove the screws.
    1. Remove the pin-type retainers.
    1. Remove the front fender splash shield.
    sy1~us~en~file=gn2615a.gif~gen~ref.gif
  1. Remove the cowl grille.
  1. On RH front fender, remove the antenna mast.
    sy1~us~en~file=k21762b.gif~gen~ref.gif
  1. On RH front fender, remove the antenna base.
    1. Remove the radio antenna base cap (18A927) by gently inserting a thin straight-edged screwdriver underneath the cap and carefully following inside the perimeter until both snaps are free.
    1. Remove the screws.
    1. Lift the antenna base.
    1. Disconnect the radio antenna lead-in cable (18812) and remove the antenna base.
    sy1~us~en~file=k22299b.gif~gen~ref.gif
  1. Remove the fender stuffer.
  1. Remove the stone guard.
    1. Remove the pin-type retainers.
    1. Remove the stone guard.
    sy1~us~en~file=gn2618a.gif~gen~ref.gif
  1. Remove the front fender.
    • Remove the bolts.

Sep 17, 2014 | 2000 Ford F150 Flareside SuperCab

1 Answer

Trying to remove the battery from my 2007 soltice


Hello robert.... Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .


Joe
Thanks for choosing Fixya!

Jan 30, 2011 | 2007 Pontiac Solstice Convertible

1 Answer

Where is the battery located?


Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure . 1737d1122299169-solstice-service-battery-replacement-procedures-158wilmingtoncarshow36.jpg
hope this helps . please rate my response.

Nov 28, 2010 | 2007 Pontiac Solstice Convertible

1 Answer

What side of the block is the crankshaft positioning sensor located on a 1993 olds cutlas supreme?


prev.gif next.gif REMOVAL & INSTALLATION Fig. 1: Crankshaft Position (CKP) sensor mounting 88004g85.gif
Fig. 2: The 24X CKP sensor is mounted to the engine front cover - 3.1L (VIN M) engine 88004g89.gif
2.2L, 2.3L, 3.1L (VIN T and V) and 1991-93 3.4L Engines
  1. Disconnect the negative battery cable.
  2. Detach the sensor harness connector from the sensor.
  3. Unfasten the sensor retaining bolts, then remove the sensor from the engine.
  4. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  5. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor. Install the sensor into the engine.
  6. Install the sensor retaining bolt. Tighten to 88 inch lbs. (10 Nm).
  7. Attach the sensor harness connector.
  8. Connect the negative battery cable.
2.5L Engine
  1. Disconnect the negative battery cable.
  2. Remove the DIS assembly, as outlined in Section 2 of this manual.
  3. Remove the sensor retaining screws and remove the sensor from DIS assembly.
  4. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  5. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor.
  6. Fit the sensor to the DIS assembly and install the retaining screws. Tighten the retaining screws to 20 inch lbs. (2.3 Nm).
  7. Install the DIS assembly to the engine, as outlined in Section 2 of this manual.
  8. Connect the negative battery cable.
3.1L (VIN M) Engines 3X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Turn the steering wheel to the full left position.
  3. Raise and safely support the vehicle.
  4. Detach the sensor harness connector from the sensor.
  5. Unfasten the sensor retaining bolts, then remove the sensor from the engine.
  6. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  7. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor. Install the sensor into the engine.
  8. Install the sensor retaining bolt. Tighten to 71 inch lbs. (8 Nm).
  9. Attach the sensor harness connector.
  10. Carefully lower the vehicle.
  11. Turn the steering wheel to the straight ahead position, then connect the negative battery cable.
24X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. If necessary for access, remove the right front wheel and inner fender access cover.
  5. Unfasten the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer using tool J 24420-B.
  6. Detach the sensor electrical connector.
  7. Unfasten the sensor retaining bolts, then remove the sensor from the vehicle. To install:
  8. Install the CKP sensor and secure using the retaining bolts. Tighten the bolts to 8 ft. lbs. (10 Nm).
  9. Attach the sensor electrical connector.
  10. Install the balancer on the crankshaft using special tool J 29113, or equivalent.
  11. Apply thread sealer 1052080 or equivalent to the bolt threads of the crankshaft balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm).
  12. If removed, install the inner fender shield and the right front wheel and tire assembly. Tighten the wheel lug nuts to 100 ft. lbs. (140 Nm).
  13. Carefully lower the vehicle.
  14. Install the serpentine belt.
  15. Connect the negative battery cable.
1994-96 3.4L Engine 3X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the intermediate exhaust pipe.
  4. Remove the rack and pinion heat shield.
  5. Remove the alternator cooling duct.
  6. Detach the sensor electric connector.
  7. Remove the 3X CKP sensor from the engine.
  8. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  9. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor. Install the sensor into the engine.
  10. Install the sensor-to-block bolt and tighten to 71 inch lbs. (8 Nm).
  11. Attach the sensor connector.
  12. Install the alternator cooling duct.
  13. Install the rack and pinion heat shield.
  14. Install the intermediate exhaust pipe.
  15. Connect the negative battery cable.
24X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel and inner fender access cover.
  5. Unfasten the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer using tool J 38197, or equivalent.
  6. Detach the sensor electrical connector.
  7. Unfasten the sensor retaining bolts, then remove the sensor from the vehicle. To install:
  8. Install the CKP sensor and secure using the retaining bolts. Tighten the bolts to 8 ft. lbs. (10 Nm).
  9. Attach the sensor electrical connector.
  10. Install the balancer on the crankshaft.
  11. Apply thread sealer 1052080 or equivalent to the bolt threads of the crankshaft balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm).
  12. If removed, install the inner fender shield and the right front wheel and tire assembly. Tighten the wheel lug nuts to 100 ft. lbs. (140 Nm).
  13. Carefully lower the vehicle.
  14. Install the serpentine belt.
  15. Connect the negative battery cable.
3.8L Engine
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel and inner fender access cover.
  5. Using a 28mm socket, unfasten the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer using tool J 38197, or equivalent.
  6. Remove the CKP sensor shield. Do NOT use a prybar to remove the shield!
  7. Detach the sensor electrical connector.
  8. Unfasten the sensor retaining bolts, then remove the sensor from the block face. To install:
  9. Position the CKP sensor to the block face, then secure using the retaining bolts. Tighten the bolts to 14-28 ft. lbs. (20-40 Nm).
  10. Install the CKP sensor shield.
  11. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Apply thread sealer 1052080 or equivalent to the bolt threads of the crankshaft balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm), plus an additional 76°turn.
  14. Install the inner fender shield and the right front wheel and tire assembly. Tighten the wheel lug nuts to 100 ft. lbs. (140 Nm).
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. Connect the negative battery cable.
prev.gif next.gif

Nov 12, 2010 | 1993 Oldsmobile Cutlass Supreme

2 Answers

My antena wont go down ,and the motor wont go off , even when the car is shut off .


Unplug the harness to the ant.It will not go off,until you replace the whole ant.mass.The gear(plastic)are stripped out,and the motor can not sense that the any.is moving.

Jan 19, 2010 | 1991 Oldsmobile Eighty Eight

1 Answer

Where is the starter for a 1995 oldsmobile 98 regency elite


The starter motor for your Oldsmobile is mounted at the front lower part of the engine, just behind the radiator.
Book time to replace by an experience person is 1.1 hours.
If you are looking to do this yourself, disconnect the battery negative terminal and isolate it.
Remove any covers or braces in order to access and remove the starter.
Remove the wires to the solenoid on the starter, then the bolts retaining the starter to the engine.
There may be some shims between the starter and the engine. You may need to replace these with the new starter.
Hope your repair goes well.

KL

Dec 16, 2009 | 1994 Oldsmobile Ninety Eight Regency

1 Answer

Alternator removal 1998 ford taurus dohc


3.0L (4V)
Removal
  1. Disconnect the battery ground cable.
  1. Remove the accessory drive belt from the generator pulley.
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist.
  1. Remove the right front wheel.
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.

Nov 08, 2009 | 1998 Ford Taurus

2 Answers

Dead battery


Removal Procedure

Disconnect the negative battery cable

Remove the wheelhouse liner.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.


Install the battery hold down retainer and bolt.

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts.

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Install the positive battery cable (1).

Tighten the positive battery cable bolt.

Close the positive battery cable connection cover.

Install the wheelhouse liner.

Connect the negative battery cable

Oct 15, 2009 | 2006 Pontiac Solstice

1 Answer

How to 1998 Taurus altenator R&R


please rate highly if this helps
Generator 3.0L (2V)
Removal
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  2. Remove the right front wheel. Refer to Section 00-02 .
  3. Remove the lower fender splash shield retainers and position the shield out of the way.
  4. Lower the vehicle.
  5. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  6. Remove the power steering line bracket and heater hose support bracket from the generator.
  7. Remove the upper generator bolts.
  8. Remove the generator splash shield.
  9. Raise the vehicle.
  10. Disconnect the electrical connector and remove the battery positive cable from the generator.
  11. Position an adjustable stand to the subframe.
  12. Remove the right subframe bolts.
  13. Remove the lower generator bolt.
  14. Disconnect the right hand stabilizer link.
  15. Lower the subframe to provide clearance.
  16. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Connect the right hand stabilizer link and torque to 47-62 Nm (35-46 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B + cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
3.0L (4V)
Removal
  1. Disconnect the battery ground cable. For additional information, refer to Section 14-01 .
  1. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  1. Remove the right front wheel. Refer to Section 00-02 .
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.
3.4L (4V)
Removal
  1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the right side cowl vent screen. Refer to Section 01-02 .
  1. Raise the vehicle and remove right front wheel assembly. Refer to Section 00-02 .
  1. Remove right tie-rod. Refer to Section 11-02 .
  1. Remove accessory drive belt (8620) from generator. Refer to Section 03-05 .
  1. Disconnect electrical harness connector and output terminal wiring.
  1. Remove nut and position engine control sensor wiring (12A581) out of the way.
  1. Remove the two bolts and one stud bolt.
  1. Remove generator from vehcile

May 12, 2009 | 1998 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...